Slat 5
Figure 002
1EFF : ALL 1 57-46-00 Page 3
1 1 Feb 01/98
1 1
1CES 1
Two girders, made from pressed aluminum alloy sheet, add strength to the structure and attach the top and the bottom skins to the spar. The top girder is corrugated to let air from the anti-icing system flow through to the bottom skin.
There are seals attached to the rear face of the slat:
-at the inboard end of the slat
-around the tracks
-near the forward joint of the top and bottom skins.
Elbow pieces reinforce the seals at each corner.
A weather-seal strip closes the area between Slat 4 (Ref. 57-45-00) and Slat 5. The strip is installed in parallel channels attached to the rear face of the top skin of the slats.
B. Trailing Edge Structure
The slat 5 has a trailing edge structure which is attached to the the main rivetted structure at the rear spar. It closes the aft edge of the slat and completes the aerodynamic profile.
The trailing edge is a bonded structure of aluminum alloy panels with a honeycomb core.
C. Slat Tracks
The slat 5 is connected to slat-tracks 11 and 12. Each slat-track is made from a curved steel forging and has a rack attached by bolts to its bottom face. A pinion on the slat-track actuator turns to move the rack and thus extends or retracts the slat. Fixed stops at the ends of the slat-track limit the travel of the slat.
The slat-tracks are connected to the track ribs of slat 5 with bolts, nuts and titanium alloy links. A closing plate and self-aligning bearings are attached to the forward end of each slat-track. Eccentric bushes are installed in the slat-track ribs for adjustment of the slat.
D. Attachments for the Wing Anti-icing System
A piccolo tube goes through the slat ribs from the inboard end, and is closed at the outboard end. It is connected to the outboard end of Slat 4 by a flexible hose. The slat top girder is corrugated to let the air from the piccolo tube flow through the exhaust holes in the bottom skin.
SLAT 5 - INSPECTION/CHECK
_________________________
TASK 57-46-00-200-001
Special Detailed Inspection of Slat 5, Tracks 11 and 12: Visible Part of Roller Contact Area
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 574601-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific adjustable access platform 3.5 m (11 ft. 6 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1 R SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 27-80-00-866-004 27-80-00-866-005 NTM 57-46-01 PART 6 ASRM 574000 57-46-00-991-001 Extending the Slats on the GroundRetracting the Slats on the Ground (for corrective action)Fig. 601
3. Job Set-up__________
Subtask 57-46-00-941-050
A. Safety Precautions
(1) Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2) Put the safety barriers in position.
Subtask 57-46-00-860-050
B. Aircraft Maintenance Configuration
(1) Fully extend the slats (Ref. TASK 27-80-00-866-004).
R (2) Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.
R R (3) Put the adjustable access platform below the applicable wing leading edge at slat 5, zone 515(615).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(67)
