R (5) Fill the clearance between the access panel (2) and the trailing edge
R of the wing skin with SEALANTS (Material No. 09-016).
R 5. Close-up________
R Subtask 57-51-37-942-053
R A. Removal of Equipment
R (1) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (2) Remove the access platform(s).
R (3) Remove the safety barriers.
R (4) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (Ref. TASK 27-00-
R 00-080-002) from the flap/slat control lever.
R (5) Remove the warning notice(s).
TASK 57-51-37-000-004
Removal of the Access Panels 575AB/575BB/575CB/575DB/575EB/575FB/575GB/575HB (675AB/675BB/675CB/675DB/675EB/675FB/675GB/675HB)
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
R R Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice
No specific adjustable access platform 4 m (13 ft. 1 in.)
98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
R B. Referenced Information
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 27-00-00-480-002 Installation of the Flap/Slat Control-Lever Locking
R Tool (98D27803000000)
R 27-50-00-866-009 Retraction of the Flaps on the Ground
R 57-51-37-991-005 Fig. 403
R 3. Job Set-up__________
R (Ref. Fig. 403/TASK 57-51-37-991-005)
R Subtask 57-51-37-941-056
R A. Safety Precautions
R (1) Put the warning notice in the cockpit to tell persons not to operate
R the flaps/slats.
R (2) Make sure that the flaps/slats are fully retracted (Ref. TASK 27-50-
R 00-866-009) and install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
R (98D27803500001) (Ref. TASK 27-00-00-480-002) on the flap/slat
R control lever.
R Put the safety barriers in position.
R Subtask 57-51-37-010-054
R B. Get Access
R (1) Put the adjustable access platform below the applicable access panel,
R zone 575(675).
R 4. Procedure_________
R CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING_______
R EDGE:
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
R - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY.
R INCORRECT INSTALLATION CAN CAUSE DAMAGE.
R Lower Trailing Edge Access Panels - Rib 10 to Rib 22 R Figure 403/TASK 57-51-37-991-005- 14 (SHEET 1)
1EFF : ALL 1 57-51-37Page 420 1 1 Aug 01/02 1 1 1CES 1R Lower Trailing Edge Access Panels - Rib 10 to Rib 22 R Figure 403/TASK 57-51-37-991-005- 24 (SHEET 2)
1EFF : ALL 1 57-51-37Page 421 1 1 Aug 01/02 1 1 1CES 1R Lower Trailing Edge Access Panels - Rib 10 to Rib 22 R Figure 403/TASK 57-51-37-991-005- 34 (SHEET 3)
1EFF : ALL 1 57-51-37Page 422 1 1 Aug 01/02 1 1 1CES 1R Lower Trailing Edge Access Panels - Rib 10 to Rib 22 R Figure 403/TASK 57-51-37-991-005- 44 (SHEET 4)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(165)
