(2)
Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the inspection area of slat track 6 shown.
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-227,
Subtask 57-43-00-210-055
B. Inspection
(1) Examine the slat 2, tracks 5 and 6 attachment links, side plates, track rib lugs and track lugs. Make sure that:
-there is no corrosion, cracks or damage
-the sealant is in a serviceable condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 574000) for the
____
correct repair procedure.
(2) Examine each slat attachment bolt as follows: NOTE : Remove one of the attachment bolts, examine it and install it
____ correctly before removing a different bolt for inspection. Do not remove more than one attachment bolt at any time.
(a) Remove one of the slat attachment bolts on slat tracks 5 or 6 (Ref. TASK 27-84-64-000-001).
Details of the Slat Track 5 Link Sideplates and Bolts R Figure 605/TASK 57-43-00-991-006
1EFF : ALL 1 57-43-00Page 626 1 1 Nov 01/99 1 1 1CES 1
Details of the Slat Track 6 Link Sideplates and Bolts R Figure 606/TASK 57-43-00-991-007
1EFF : ALL 1 57-43-00Page 627 1 1 Nov 01/99 1 1 1CES 1
R Slat 2, Track 5 - Inspection Details Figure 607/TASK 57-43-00-991-009
1EFF : 1 1 1CES ALL 1 111 57-43-00 Page 628 Nov 01/99
R Slat 2, Track 6 - Inspection Details Figure 608/TASK 57-43-00-991-010
1EFF : 1 1 1CES ALL 1 111 57-43-00 Page 629 Nov 01/99
(b) Examine the attachment bolt. Make sure that:
-there is no corrosion or damage
-
the shank of the bolt is not worn
-
the bolt hole is not worn or damaged.
NOTE : If necessary, discard the worn/damaged bolt and install a
____
replacement item.
(c)
Install the slat attachment bolt (Ref. TASK 27-84-64-400-002).
(d)
Do steps (a) thru (c) for each attachment bolt on the slat tracks 5 and 6 attachment links and side plates.
R **ON A/C 106-149, 228-299, 301-399, 401-499,
Subtask 57-43-00-210-055-A
B. Inspection
(1)
Do an inspection of the slat track 5 and 6 attachments in the areas shown.
(2)
Make sure that there is no corrosion, cracks or damage and that the sealant is in a serviceable condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 574000) for the
____
correct repair procedure.
**ON A/C ALL
5. Close-up
________
Subtask 57-43-00-410-056
A. Close Access
(1) Remove the access platform(s).
Subtask 57-43-00-865-065
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
Subtask 57-43-00-860-059
C. Aircraft Configuration
(1) Fully retract the slats (Ref. TASK 27-80-00-866-005). Subtask 57-43-00-942-064
D. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
SKINS AND PLATING - CLEANING/PAINTING
_____________________________________
TASK 57-43-11-300-001
Cleaning and Painting of the No. 2. Slat
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(40)
