C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-80-00-866-004 Extending the Slats on the Ground
27-80-00-866-005 Retracting the Slats on the Ground
R NTM 57-45-01 PART 6 ASRM 574000 (for corrective action) 57-45-00-991-001 Fig. 601
3. Job Set-up
__________
Subtask 57-45-00-941-050
A. Safety Precautions
(1) Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2) Put the safety barriers in position.
Subtask 57-45-00-860-050
B. Aircraft Maintenance Configuration
(1)
Extend the slats fully (Ref. TASK 27-80-00-866-004).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.
R (3) Put the access platform below the applicable wing leading edge at R slat 4, zone 522(622).
Subtask 57-45-00-865-050
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
4. Procedure
_________
(Ref. Fig. 601/TASK 57-45-00-991-001) Subtask 57-45-00-110-050
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the roller contact area of the slat tracks 9 and 10.
Subtask 57-45-00-280-050
B. Inspection
(1) Do a special detailed inspection of the roller contact area of the slat tracks 9 and 10 (Ref. NTM 57-45-01 PART 6).
NOTE : If necessary, refer to the ASRM (Ref. ASRM 574000) for the
____ correct repair procedure. If the defect is not included in this repair, you must request a procedure from Airbus Industrie.
5. Close-up
________ Subtask 57-45-00-865-051
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
Subtask 57-45-00-860-051
B. Aircraft Configuration
(1) Retract the slats fully (Ref. TASK 27-80-00-866-005). Subtask 57-45-00-942-051
C. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 57-45-00Page 603 1 1 May 01/05R 1 1 1CES 1
R Details of the Roller Contact Area of Slat Tracks 9 and 10 Figure 601/TASK 57-45-00-991-001
1EFF : ALL 1 57-45-00Page 604 1 1 May 01/05 1 1 1CES 1
(3)
Remove the access platform(s).
(4)
Remove the safety barriers.
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-45-00Page 605 1 1 May 01/05R 1 1 1CES 1
TASK 57-45-00-200-005
R Detailed Inspection of Slat 4, Skin Connections in Area of Lower Girder at Track Rib Stations, LH/RH
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 574504-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific adjustable access platform 3.5 m (11 ft. 6 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM WINGS 机翼3(57)