-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575158-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform No specific safety barriers No specific warning notices 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
1EFF : ALL 1 57-51-00Page A661 1 1 Nov 01/04R 1 1 1CES 1
C. Referenced Information -------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
ASRM 575100 (for corrective action)
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
57-51-00-991-027 Fig. 627
**ON A/C 301-399,
57-51-00-991-027-A Fig. 627A
**ON A/C ALL
3. Job Set-up
__________
Subtask 57-51-00-941-082
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(3)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
Subtask 57-51-00-010-085
B. Get Access
(1) Put the adjustable access platform in position at the applicable zone 500 (600).
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 627/TASK 57-51-00-991-027)
**ON A/C 301-399,
(Ref. Fig. 627A/TASK 57-51-00-991-027-A)
**ON A/C ALL
Subtask 57-51-00-100-050
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean applicable area for inspection.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-00-210-073
B. General Visual Inspection of Outer Wing, Bottom Skin Lower Surface, Aft of Rear Spar between Rib 1 and Rib 9, Excluding Areas Covered by Flap Track 2 Fairings and Pylon Fairings
(1) Do an inspection and make sure that:
-
there is no damage
-
there are no cracks
-
there is no corrosion
-the paint finish is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
Bottom Skin Lower Surface, Aft of Rear Spar Between Rib 1 and Rib 9 -Inspection Area
Figure 627/TASK 57-51-00-991-027
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-51-00Page A664 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Bottom Skin Lower Surface, Aft of Rear Spar Between Rib 1 and Rib 9 -Inspection Area R Figure 627A/TASK 57-51-00-991-027-A
R 1EFF : 301-399, 1 57-51-00Page A665 1 1 Nov 01/04 1 1 1CES 1
**ON A/C 301-399,
Subtask 57-51-00-210-073-A
B. General Visual Inspection of Outer Wing, Bottom Skin Lower Surface, Aft of Rear Spar between Rib 1 and Rib 9, Excluding Areas Covered by Flap Track 2 Fairings, Pylon Fairings and Flap Tab Drive 1a Fairings
(1) Do an inspection and make sure that:
-
there is no damage
-
there are no cracks
-
there is no corrosion
-the paint finish is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
**ON A/C ALL
5. Close-up
________ Subtask 57-51-00-942-083
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the warning notice(s).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(119)
