-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-33-560-051
A. Preparation of a Replacement Component WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(2)
Apply a layer of SEALANTS (Material No. 09-001) to the shims (12).
(3)
Put all the shims (12) and the bearing pads (11) in position.
(4)
Install the bolts (9) and the nuts (13).
(5)
Install the studs (8), the washers (14) and the nuts (15).
(6)
TORQUE the nuts (15) to between 2.26 and 2.4 m.daN (16.66 and 17.69 lbf.ft).
(7)
Install the new cotter pins (16).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-51-33Page 460 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C 301-399,
R Subtask 57-51-33-560-051-A
R A. Preparation of a Replacement Component
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______
R MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
R DO NOT BREATHE THE GAS.
R THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
R GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R (1) Make sure that the parts retained from the removed component are
R clean and in the correct condition.
R (2) Apply a layer of SEALANTS (Material No. 09-001) to the shims (12).
R (3) Put the set of shims (12) and the bearing pads (11) in the positions
R that they were removed from (do one side at a time).
R (4) Install the bolts (9) and the nuts (13).
R (5) Install the studs (8), the washers (14) and the nuts (15).
R (6) TORQUE the nuts (15) to between 2.26 and 2.4 m.daN (16.66 and 17.69
R lbf.ft).
R (7) Install the new cotter pins (16).
R **ON A/C ALL
Subtask 57-51-33-420-069
B. Preparation for Installation
(1) Clean the component interfaces and the adjacent areas with a
MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS
(Material No. 11-026).
(2) Do an inspection of the component interface and/or the adjacent area.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-33-420-056
C. Installation of the Flap Track Beam
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME DAMAGED OR
_______ INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
NOTE : The weight of the flap track beam (1) is 36 kg (79.3663 lb).
____
(1) Lift and hold the flap track beam (1).
NOTE : Steps 2,3 and 4 must be completed carefully and as one
____ continuous procedure. Unsatisfactory work will result in damage to the spigot chrome protection and/or the top flange of the beam. in the recess in the wing.
(2)
Lift the rear end of the flap track beam (1). Engage the failsafe spigot (10) through the bush in the bottom skin plate.
(3)
At the rear mounting:
(a)
Apply SPECIAL MATERIALS (Material No. 05-002) to the aft spigot pin (17), but not to the thread.
(b)
Install the spherical washer (4).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(152)
