-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575101-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notices 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
1EFF : ALL 1 57-51-00Page 634 1 1 Aug 01/02R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
57-55-11-000-001 Removal of the Flap Track Fairings Nos. 2, 3 and 4 R 57-55-11-000-004 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-001 Installation of the Flap Track Fairings Nos. 2, 3 and
4 R 57-55-11-400-004 Installation of the Flap Track Fairings Nos. 2, 3 and R 4
ASRM 575100 (for corrective action)
57-51-00-991-006 Fig. 607
3. Job Set-up
__________
Subtask 57-51-00-941-061
A. Safety Precautions
(1)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER on the flap/slat control lever.
(2)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(3)
Put the safety barriers in position.
Subtask 57-51-00-865-058
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-00-010-054
C. Get Access
(1)
Put the access platform in position below zone 530 (630).
(2)
Remove the applicable access panels (Ref. TASK 57-55-11-000-001):
-for the left wing, remove 531CB, 532CB, 533CB
-for the right wing, remove 631CB, 632CB, 633CB.
**ON A/C 301-399,
Subtask 57-51-00-010-054-A
C. Get Access
(1)
Put the access platform in position below zone 530 (630).
(2)
Remove the applicable access panels (Ref. TASK 57-55-11-000-004):
-
for the left wing, remove 531CB, 532CB, 533CB
-
for the right wing, remove 631CB, 632CB, 633CB.
R **ON A/C ALL
4. Procedure
_________
(Ref. Fig. 607/TASK 57-51-00-991-006)
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-51-00-110-056
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the flap actuator brackets at tracks 2, 3 and 4.
Subtask 57-51-00-210-068
B. Inspection
(1) Examine the flap actuator brackets at tracks 2, 3 and 4 for:
-corrosion
-damage
-scratches and scores
-correct condition of protective finish.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
Flap Actuator Brackets Figure 607/TASK 57-51-00-991-006
1EFF : 1 1R 1CES ALL 1 11 1 57-51-00 Page 638 May 01/04
5. Close-up
________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(89)
