R R Slat 4, Track 10 - Inspection Details Figure 606/TASK 57-45-00-991-010
1EFF : 1 1 1CES ALL 1 111 57-45-00 Page 627 May 01/98
Details of the Slat Track 9 Link Sideplates and Bolts Figure 607/TASK 57-45-00-991-002
1EFF : ALL 1 57-45-00Page 628 1 1 Nov 01/99R 1 1 1CES 1
Details of the Slat Track 10 Link Sideplates and Bolts
Figure 608/TASK 57-45-00-991-003
1EFF : ALL 1 57-45-00Page 629 1 1 Nov 01/99R 1 1 1CES 1
(b) Examine the attachment bolt. Make sure that:
-there is no corrosion or damage
-
the shank of the bolt is not worn
-
the bolt hole is not worn or damaged.
NOTE : If necessary, discard the worn/damaged bolt and install a
____
replacement item.
(c)
Install the slat attachment bolt (Ref. TASK 27-84-66-400-002).
(d)
Do steps (a) thru (c) for each attachment bolt on the slat tracks 9 and 10 attachment links and side plates.
R **ON A/C 106-149, 228-299, 301-399, 401-499,
Subtask 57-45-00-210-055-A
B. Inspection
(1)
Do an inspection of the slat track 9 and 10 attachments in the areas shown.
(2)
Make sure that there is no corrosion, cracks or damage and that the sealant is in a seviceable condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 574000) for the
____
correct repair procedure.
**ON A/C ALL
5. Close-up
________
Subtask 57-45-00-410-056
A. Close Access
(1) Remove the access platform(s).
Subtask 57-45-00-865-065
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
Subtask 57-45-00-860-059
C. Aircraft Configuration
(1) Retract the slats fully (Ref. TASK 27-80-00-866-005). Subtask 57-45-00-942-064
D. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
SKINS AND PLATES - CLEANING/PAINTING
____________________________________
TASK 57-45-11-300-001
Cleaning and Painting of the No. 4. Slat
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific SCOTCHBRITE-pad
No specific access platform 3 m (9 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 07-003 R ABRASION RESISTANT COATING (TEFLON POLYURET) (Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-80-00-866-004 Extending the Slats on the Ground 27-80-00-866-005 Retracting the Slats on the Ground 51-75-12-300-001 Repair of Major Paint Damage on Light Alloy and
Composite Material 57-45-11-991-001 Fig. 701
3. Job Set-up
__________ Subtask 57-45-11-941-050
A. Safety Precautions
(1) Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(62)
