Subtask 57-43-00-860-055
B. Aircraft Maintenance Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever.
(4) Fully retract the slats (Ref. TASK 27-80-00-866-005). Subtask 57-43-00-942-055
C. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the safety barriers.
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-43-00Page 615 1 1 May 01/02R 1 1 1CES 1
Details of the Slat 2 Skin Connection in the area of the Lower Girder (Track
Ribs 5 and 6)
Figure 603/TASK 57-43-00-991-003- 12 (SHEET 1)
Details of the Slat 2 Skin Connection in the area of the Lower Girder (Track
Ribs 5 and 6)
Figure 603/TASK 57-43-00-991-003- 22 (SHEET 2)
TASK 57-43-00-200-007
Special Detailed Inspection of Slat 2, Tracks 5 and 6: Visible Part of Roller R Contact Area when Slat is Fully Extended, LH/RH
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 574301-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific adjustable access platform 3.5 m (11 ft. 6 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-80-00-866-004 Extending the Slats on the Ground
27-80-00-866-005 Retracting the Slats on the Ground
NTM 57-43-01 PART 6
ASRM 574000 (for corrective action)
57-43-00-991-008 Fig. 604
3. Job Set-up
__________
Subtask 57-43-00-941-056
A. Safety Precautions
R (1) Put warning notices in the cockpit to tell persons not to operate the R flaps or slats.
(2) Put the safety barriers in position.
Subtask 57-43-00-860-056
B. Aircraft Maintenance Configuration
(1)
Fully extend the slats (Ref. TASK 27-80-00-866-004).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.
(3)
Put the adjustable access platform below the applicable wing leading edge at slat 2, zone 521(621).
Subtask 57-43-00-865-062
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
4. Procedure
_________ (Ref. Fig. 604/TASK 57-43-00-991-008) Subtask 57-43-00-110-059
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the roller contact area of slat track 5 and 6.
Subtask 57-43-00-280-052
B. Inspection
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM WINGS 机翼3(38)