-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-51-00-110-088
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the lower flange of the false rear spar forward face (RIB7 thru RIB9).
Subtask 57-51-00-210-062
B. Inspection
(1) Use a flashlight and an inspection mirror and make a detailed visual inspection of the lower flange of the false rear spar forward face (RIB7 thru RIB9). Make sure that:
-
there is no damage
-
there are no cracks and/or scores
-
there is no corrosion
-the surface protection is in the correct condition
-no water has entered the wing structure.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
1EFF : ALL 1 57-51-00Page A629 1 1 May 01/04R 1 1 1CES 1
Outer Wing - False Rear Spar Figure 621/TASK 57-51-00-991-022
1EFF : 1 1R 1CES ALL 1 11 1 57-51-00 Page A630 May 01/04
5. Close-up
________
Subtask 57-51-00-410-074
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
R (2) Install the access panels:
R - for the left wing, install 573BB, 573CB, 573DB, 573EB
R - for the right wing, install 673BB, 673CB, 673DB, 673EB.
Subtask 57-51-00-865-090
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-51-00-942-073
C. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(3)
Remove the warning notice(s).
(4)
Remove the safety barriers.
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R TASK 57-51-00-200-011
R Detailed Inspection of Outer Wing, Bottom Skin Panel No. 3, Upper Surface,
R Between Rear Spar and False Rear Spar, and Between Gear Support RIB5 and RIB8.
R WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______
R GEAR.
R WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______
R START A TASK ON OR NEAR:
R - THE FLIGHT CONTROLS
R - THE FLIGHT CONTROL SURFACES
R - THE LANDING GEAR AND THE RELATED DOORS
R - COMPONENTS THAT MOVE.
R CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
R - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY.
R INCORRECT INSTALLATION CAN CAUSE DAMAGE.
R 1. Reason for the Job__________________
R Refer to the MPD TASK: 575167-01
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific circuit breaker(s) safety clip(s)
R No specific safety barriers
R No specific warning notices
R No specific access platform 2.5 m (8 ft. 2 in.)
R 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
R B. Consumable Materials
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. 11-026 GB DEF-STAN 68-148/1
R SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
R Material No. 19-003 USA AMS 3819
R LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R C. Referenced Information
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(111)
