R 1EFF : 301-399, 1 57-51-00Page A625 1 1 May 01/04 1 1 1CES 1
R Subtask 57-51-00-942-082
R C. Removal of Equipment
R (1) Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat
R control lever.
R (2) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (3) Remove the access platform(s).
R (4) Remove the warning notice(s).
R (5) Remove the safety barriers.
R (6) Remove the ground support and maintenance equipment, the special and
R standard tools and all other items.
R 1EFF : 301-399, 1 57-51-00Page A626 1 1 May 01/04 1 1 1CES 1
R **ON A/C ALL
TASK 57-51-00-200-010
Detailed Visual Inspection of Outer Wing False Rear Spar Forward Face Lower Flange between Ribs 7 and 9
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575166-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific flashlight No specific inspection mirror No specific safety barriers No specific warning notices No specific access platform 2.5 m (8 ft. 2 in.) 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 575100 (for corrective action) 57-51-00-991-022 Fig. 621
3. Job Set-up
__________ Subtask 57-51-00-941-072
A. Safety Precautions
(1)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2)
Put the safety barriers in position.
(3)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
Subtask 57-51-00-865-089
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
1EFF : ALL 1 57-51-00Page A628 1 1 May 01/04R 1 1 1CES 1
Subtask 57-51-00-010-073
C. Get Access
(1)
Put the access platform below the applicable wing at the false rear spar, zone 570(670).
(2)
Remove the access panels:
-
for the left wing, remove 573BB, 573CB, 573DB, 573EB
-
for the right wing, remove 673BB, 673CB, 673DB, 673EB.
4. Procedure
_________
(Ref. Fig. 621/TASK 57-51-00-991-022)
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼3(110)
