(2)
Remove the access panel 321AL.
4. Procedure
_________ Subtask 24-92-00-210-068
A. Inspection
(Ref. Fig. 628/TASK 24-92-00-991-033)
(1) Do a general visual inspection of the components on these harnesses:
-4202VB,
-4204VB.
(a)
Do a check of the general condition of these components and make sure that they are correctly attached:
-electrical bonding leads,
-braided conduits,
-clamps,
-electrical connectors, braided shields.
(b)
Make sure that there is no sign of contamination (Ref. ESPM 205500) and corrosion (Ref. ESPM 205332).
1EFF : ALL 1 24-92-00Page 693 1 1 May 01/04R 1 1 1CES 1
Electrical Harnesses - Inspection Figure 628/TASK 24-92-00-991-033
1EFF : 1 1R 1CES ALL 1 11 1 24-92-00 Page 694 May 01/04
5. Close-up
________ Subtask 24-92-00-410-069
A. Close Access
(1) Install the access panel 321AL. Subtask 24-92-00-860-072
B. Aircraft Maintenance Configuration
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
1EFF : ALL 1 24-92-00Page 695 1 1 May 01/04R 1 1 1CES 1
TASK 24-92-00-210-020
General Visual Inspection of Elements Fitted on the Following Harnesses: 4202VB, 4204VB WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1.
Reason for the Job
__________________
Refer to the MPD TASK: 200003-02
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform 9 m (29 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ESPM 205332 ESPM 205500 24-92-00-991-034 Fig. 629
1EFF : ALL 1 24-92-00Page 696 1 1 May 01/04R 1 1 1CES 1
3. Job Set-up
__________ Subtask 24-92-00-860-073
A. Aircraft Maintenance Configuration
(1)
Put a warning notice in the cockpit to tell persons not to operate the pitch controls.
(2)
Put a warning notice in position to tell persons not to pressurize the Green and Yellow hydraulic systems.
Subtask 24-92-00-010-069
B. Get Access
(1)
Put an adjustable access platform in position at the vertical stabilizer leading-edge.
(2)
Remove the access panel 322BL.
4. Procedure
_________ Subtask 24-92-00-210-069
A. Inspection
(Ref. Fig. 629/TASK 24-92-00-991-034)
(1) Do a general visual inspection of the components on these harnesses:
-4202VB,
-4204VB.
(a)
Do a check of the general condition of these components and make sure that they are correctly attached:
-electrical bonding leads,
-braided conduits,
-clamps,
-electrical connectors,
-braided shields.
(b)
Make sure that there is no sign of contamination (Ref. ESPM 205500) and corrosion (Ref. ESPM 205332).
1EFF : ALL 1 24-92-00Page 697 1 1 May 01/04R 1 1 1CES 1
Electrical Harnesses - Inspection Figure 629/TASK 24-92-00-991-034
1EFF : 1 1R 1CES ALL 1 11 1 24-92-00 Page 698 May 01/04
5. Close-up
________ Subtask 24-92-00-410-070
A. Close Access
(1) Install the access panel 322BL. Subtask 24-92-00-860-074
B. Aircraft Maintenance Configuration
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
1EFF : ALL 1 24-92-00Page 699 1 1 May 01/04R 1 1 1CES 1
TASK 24-92-00-210-021
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ELECTRICAL POWER 电源2(165)
