DC ESS BUS SHED - Upper and Lower ECAM Display Unit
Figure 005 (SHEET 1)
1EFF : ALL 1 24-62-00 Page 10
1 1 Feb 01/98
1 1
1CES 1
DC ESS BUS SHED - Upper and Lower ECAM Display Unit
Figure 005 (SHEET 2)
1EFF : ALL 1 24-62-00 Page 11
1 1 Feb 01/98
1 1
1CES 1
CONTACTOR (8PH) - REMOVAL/INSTALLATION
______________________________________ TASK 24-62-55-000-001 Removal of the DC Shed Essential Bus Contactor (8PH)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 1.8 m (5 ft. 11 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-62-55-991-001 Fig. 401
3. Job Set-up
__________ Subtask 24-62-55-010-050
A. Get access to the Avionics Compartment
(1)
Put an access platform in position at the avionics compartment doors 812 and 822.
(2)
Open the access doors 812 and 822.
(3)
Open the access panels of the AC/DC emergency power center 106VU and the access panels of the BATTERY power center 105VU.
Subtask 24-62-55-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
105VU ELEC/CSM/G /EV AUTO/SPLY 7XE C01
106VU CSM/G /EV/MAN/SPLY 6XE B04 R 106VU ESS TR/SPLY 4PE C01 R
122VU ELEC/CNTOR/ESS/DC BUS/TIE 3PC W26 123VU AC ESS/BUS ON/BUS 1 1XC AC12 123VU AC ESS/BUS ON/BUS 2 2XC AC01
4. Procedure
_________
(Ref. Fig. 401/TASK 24-62-55-991-001)
Subtask 24-62-55-020-050
A. Removal of the Contactor R CAUTION : REMOVE THE CONTACTOR ONLY AND NOT THE BASE OR THE MODULE WHERE
_______
THE WIRES ARE CONNECTED.
(1)
Disconnect the connector (4).
(2)
Put blanking caps on the disconnected electrical connectors.
(3)
Loosen the two captive screws (2). NOTE : Do not remove the captive screws (2) and the spring washers
____
from the contactor (3).
(4)
Disengage the contactor (3) from the base (5) and then remove the contactor.
DC Shed Essential Bus Contactor
Figure 401/TASK 24-62-55-991-001
1EFF : ALL 1 24-62-55 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 24-62-55-400-001
Installation of the DC Shed Essential Bus Contactor (8PH)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific access platform 1.8 m (5 ft. 11 in.) R No specific Torque Wrench : range 5.00 to 35.00 lbf.in R (0.05 to 0.40 m.daN)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power
24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power
31-60-00-860-001 EIS Start Procedure
31-60-00-860-002 EIS Stop Procedure
24-62-55-991-001 Fig. 401
3. Job Set-up
__________
Subtask 24-62-55-860-050
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ELECTRICAL POWER 电源2(141)
