-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND THE CAUTIONS INCLUDED IN
_______ THE REFERENCED PROCEDURES.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______ ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
1. Reason for the Job
__________________
Refer to the MPD TASK: 240000-09 Apply temporary protection to end fittings of electrical conduits in the wing tip.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific airless spray No specific brush No specific dental No specific lint-free cloth No specific seal tools No specific adjustable access platform 3 m (9 ft. 10 in.)
R 1EFF : ALL 1 24-92-00Page 617 1 1 Feb 01/04 1 1 1CES 1 B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
Material No. 15-008 AIB TN 10138 TYPE II GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-34-24-869-002 Aircraft Grounding for the Maintenance Operations 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power 24-92-00-991-006 Fig. 602 24-92-00-991-010 Fig. 606 24-92-00-991-011 Fig. 607
3. Job Set-up
__________ Subtask 24-92-00-862-054
A. De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002).
Subtask 24-92-00-869-059
B. Connect the aircraft to the ground (Ref. TASK 12-34-24-869-002). Subtask 24-92-00-010-054
C. Get Access
(1)
Put the adjustable access platform in position at the wing tip.
(2)
For the left wing.
(a) Remove and retain the access panel: 534AB.
R 1EFF : ALL 1 24-92-00Page 618 1 1 Feb 01/04 1 1 1CES 1
(3) For the right wing.
(a) Remove and retain the access panel: 634AB.
4. Procedure
_________ Subtask 24-92-00-210-054
A. Inspection of the End Fittings of Electrical Conduits (Ref. Fig. 602/TASK 24-92-00-991-006, 606/TASK 24-92-00-991-010, 607/TASK 24-92-00-991-011)
WARNING : BE CAREFUL NOT TO CUT YOUR FINGERS. FLAKES OF NICKEL ARE SHARP.
_______
(1) At each fitting use the procedure that follows to protect against corrosion:
(a)
Use CLEANING AGENTS (Material No. 11-004) and a lint-free cloth to remove any contamination from the fitting.
(b)
Remove any flakes or blisters, make sure that the you do not damage the base metal while you do this task.
NOTE : A dental or a seal tools are recommended for the removal
____
of flakes and blisters.
(c) Use a brush or an airless spray to apply a continuous coat of STORAGE PRESERVATION (Material No. 15-008) with a thickness of
0.030 mm (0.001 in.), to cover all the fitting.
5. Close-up
________ Subtask 24-92-00-410-055
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
For the left wing.
(a) Install the access panel: 534AB.
(3)
For the right wing.
(a) Install the access panel: 634AB.
R 1EFF : ALL 1 24-92-00Page 619 1 1 Feb 01/04 1 1 1CES 1
Electrical Harness Conduits Figure 606/TASK 24-92-00-991-010
R 1EFF : 1 1 1CES ALL 1 111 24-92-00 Page 620 Feb 01/04
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ELECTRICAL POWER 电源2(152)
