(3)
In the zone 131, close the sidewall and partition panels (Ref. TASK 25-54-12-400-003) and (Ref. TASK 25-54-12-400-001).
(a)
For the left IDG feeders:
-131PW, 131SW
(b)
For the right IDG feeders:
-132PW, 132SW
(4)
Close the FWD cargo-compartment door 825AR (Ref. TASK 52-30-00-860-002).
(5)
Remove the warning notice(s).
(6) Remove the access platform(s). **ON A/C 301-399,
Subtask 24-92-00-410-076-A
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close these access panels:
(a)
For the left pylon:
-414FR, 414CR, 414AR
(b)
For the right pylon:
-424ER, 424CR, 424AR, 423FL
(c)
For the left wing:
-521BT, 521EB, 521CB, 521AB
(d)
For the right wing:
-621BT, 621EB, 621CB, 621AB
(3)
In the zone 131, close the sidewall and partition panels (Ref. TASK 25-54-12-400-003) and (Ref. TASK 25-54-12-400-001).
(a)
For the left IDG feeders:
-131PW, 131RW
(b)
For the right IDG feeders:
-132PW, 132RW
(4)
Close the FWD cargo-compartment door 825AR (Ref. TASK 52-30-00-860-002).
(5)
Remove the warning notice(s).
(6)
Remove the access platform(s).
**ON A/C ALL
Subtask 24-92-00-710-051
R R C. Test
R R R (1) Energize the aircraft electrical circuits from engine 1(2) (Ref. TASK 24-41-00-861-002).
R (2) On the ECAM control panel, push the ELEC key to get the ELEC page: - Make sure that the voltage of the IDG is 115 VAC. - Make sure that the frequency of the IDG is 400Hz + or - 5Hz.
5. Close-up________
Subtask 24-92-00-942-055
A. Put the aircraft back to its initial configuration
(1) Do the EIS stop procedure (Ref. TASK 31-60-00-860-002)
ELECTRICAL ROUTING - INSPECTION/CHECK
_____________________________________
R
TASK 24-92-00-210-003
Inspection of the End Fittings of Electrical Conduits in Wing Inboard Leading-Edge
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND THE CAUTIONS INCLUDED IN
_______
THE REFERENCED PROCEDURES.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______
ONLY WITH A GOOD SUPPLY OF AIR.
OBEY THE MANUFACTURERS INSTRUCTIONS.
PUT ON PROTECTIVE CLOTHING.
DO NOT GET THEM IN YOUR MOUTH.
DO NOT SMOKE.
DO NOT BREATHE THE GAS.
THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
1. Reason for the Job
__________________
Refer to the MPD TASK: 240000-04
Apply temporary protection to end fittings of electrical conduits in wing
inboard leading-edge.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific airless spray No specific brush No specific dental No specific lint-free cloth No specific seal tools No specific adjustable access platform 3 m (9 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 15-008 AIB TN 10138 TYPE II GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ELECTRICAL POWER 电源2(149)
