_______ CONNECT THE DRAIN HOSE TO THE OVERFLOW DRAIN VALVE. MAKE SURE THAT THE DRAIN HOSE HANGS DOWN VERTICAL AND THE END OF THE HOSE IS ABOVE THE OIL LEVEL IN THE CONTAINER. WHEN YOU CONNECT THE DRAIN HOSE TO THE IDG YOU RELEASE THE OIL PRESSURE AND OIL WILL SPRAY FROM THE DRAIN HOSE.
(1)
Put a container in position under the IDG.
(2)
Remove the dust cap from the overflow drain valve.
(3)
Connect the overflow drain hose of the TANK - ENGINE OIL FILLING UP (DH13PM) to the overflow drain valve. Oil can come out of the overflow drain hose of the TANK - ENGINE OIL FILLING UP from the overflow drain valve.
(4)
Disconnect the overflow drain hose of the TANK - ENGINE OIL FILLING UP from the overflow drain valve.
(5) Install the dust cap on the overflow drain valve. Subtask 24-21-49-020-053
B. Removal of the oil-out hose from the IDG CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______ ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
(1)
Put the container below the hoses on the IDG to catch the oil when the hoses are disconnected.
(2)
Disconnect the oil-out hose (50) from the IDG (60). NOTE : Use a second wrench to hold the union on the IDG when you
(3)
Disconnect the oil-out hose (50) from the lower oil-out tube (40). NOTE : Use a second wrench to hold the fitting on the tube (40) when
____
you loosen the hose (50) coupling nut.
(4)
Put protective covers on the union on the IDG and the two ends of the oil-out hose (50).
____
loosen the hose (50) coupling nut.
(5) Remove the oil-out hose (50) from the engine. Subtask 24-21-49-020-054
C. Removal of the lower oil-out tube assembly CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______ ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
(1)
Remove the screws (15) that attach the clampshells (20) to the engine brackets at Sta. 158 (B1). (two locations).
(2)
Remove the screw (15), washer (30), nut (35) that attach the clampshell (20) to the channel.
(3)
Disconnect the lower oil-out tube (40) from the upper oil-out tube (5).
NOTE : Use a second wrench to hold the fitting on the tube (5) when
____
you loosen the tube (40) coupling nut.
(4) Put protective covers on the two ends of the lower oil-out tube (40).
(5) Remove the lower oil-out tube (40) from the engine. Subtask 24-21-49-020-055
D. Removal of the upper oil-out tube assembly CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______ ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
(1)
Remove the screw (15) that attach the clampshell (20) to the channel.
(2)
Disconnect the upper oil-out tube (5) from the IDG oil cooler. NOTE : Use a second wrench to hold the fitting on the IDG oil cooler
____
when you loosen the tube (5) coupling nut.
(3)
Put protective covers on the oil cooler fitting and on the two ends of the upper oil-out tube.
(4)
Remove the upper oil-out tube (5) from the engine.
TASK 24-21-49-400-004
Installation of the IDG Cooling Oil-out tubes and Hoses
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific protective covers
No specific warning notice(s)
No specific Torque Wrench : range 8.00 to 75.00 lbf.ft
(1.00 to 10.00 m.daN) R No specific Torque Wrench : range 5.00 to 35.00 lbf.in R (0.05 to 0.40 m.daN)
No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00 to 10.00 m.daN)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
12-13-24-612-041 IDG Servicing - Filling of the IDG with Oil or
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ELECTRICAL POWER 电源1(78)
