(3)
TORQUE the case drain plug (1) to between 55 and 75 lbf.in (0.62 and
0.84 m.daN).
(4)
Safety the case drain plug (1) with lockwire 0.032 in. (0.80 mm) dia. (Material No. CP8001) or lockwire 0.032 in. (0.80 mm) dia. (Material No. CP8002).
Subtask 24-21-00-612-072
F. Filling of the IDG with Oil
CAUTION : USE ONLY APPROVED TYPES/BRANDS OF LUBRICANTS. DO NOT MIX
_______
TYPES//BRANDS OF LUBRICANTS.
NOTE : In rain, fog or wet conditions, be careful to prevent water
____ contamination of the IDG oil during the filling procedure.
NOTE : The AMM 20-34-00 gives a list of oil brand names approved for the
____
IDG.
(1)
Remove the dust cap (3) from the pressure fill valve (7).
(2)
Connect the pressure fill hose (8) of the TANK - ENGINE OIL FILLING UP (DH13PM) to the pressure fill valve (7).
(3)
Fill the IDG with the filtered OILS (Material No. 03-002) at a maximum pressure of 35 psi (2.41 bar).
(4)
Stop the filling procedure when the quantity of oil collected from the overflow drain hose (10) of the TANK - ENGINE OIL FILLING UP (DH13PM) is 0.95 l (0.25 USgal) minimum.
Subtask 24-21-00-020-069
G. Removal of the Hoses
(1)
Disconnect the pressure fill hose (8) of the TANK - ENGINE OIL FILLING UP (DH13PM) from the pressure fill valve (7).
(2)
Install the dust cap (3) on the pressure fill valve (7).
(3)
When only drops of oil come out of the overflow drain hose (10) of the TANK - ENGINE OIL FILLING UP (DH13PM), disconnect the hose (10).
(4)
Install the dust cap (4) on the overflow drain valve (5).
1EFF : ALL 1 24-21-00Page 325 1 1 Aug 01/05R 1 1 1CES 1
Subtask 24-21-00-081-056
H. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
Subtask 24-21-00-710-061
J. Operation of the Engine
(1) Start the related engine (Ref. TASK 71-00-00-710-006) until the temperature of the IDG oil is 175 deg.F (80 deg.C).
NOTE : You can read the oil temperature on the ELEC page of the lower____ ECAM DU.
(2) Stop the engine (Ref. TASK 71-00-00-710-027).
Subtask 24-21-00-481-059
K. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
Subtask 24-21-00-680-060
L. Do the steps 4.A. thru 4.E. again.
R **ON A/C 401-499,
R Subtask 24-21-00-680-060-A
R R R L. Do the steps 4.A thru 4.B again. Replace the scavenge and the charge filters. Then, do the steps 4.D thru 4.E again.
R **ON A/C ALL
Subtask 24-21-00-612-073
M. Fill the IDG with oil or add oil to the IDG after a level check (Ref. TASK 12-13-24-612-041).
5. Close-up
________ Subtask 24-21-00-410-073
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
(3)
Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
-
FOR 1000EM1
437AL, 438AR
-
FOR 1000EM2
447AL, 448AR
(4) Remove the warning notice(s). Subtask 24-21-00-862-059
B. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
1EFF : ALL 1 24-21-00Page 327 1 1 Aug 01/05R 1 1 1CES 1
TASK 24-21-00-612-043- 01
Servicing of the IDG after Oil Chemical Contamination and Extension of the Oil-Filter Differential-Pressure Indicator (DPI)
WARNING : BE CAREFUL WHEN YOU WORK ON THE ENGINE COMPONENTS IMMEDIATELY AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS CAN STAY HOT FOR UP TO ONE HOUR.
WARNING : WEAR GOGGLES, INSULATED GLOVES AND OTHER PROTECTIVE CLOTHES.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ELECTRICAL POWER 电源1(53)
