-
IF IT DOES NOT CONTAIN ENOUGH OIL
IF YOU DO, YOU CAN CAUSE DAMAGE TO THE IDG.
CAUTION : USE ONLY NEW CANS OF OIL WHEN YOU FILL THE IDG WITH OIL OR ADD OIL TO
_______ THE IDG. THE CONTAMINATION IN OIL THAT STAYS IN OPEN CANS CAN CAUSE FAST DETERIORATION OF THE OIL AND WILL DECREASE THE LIFE OF THE IDG.
CAUTION : DO NOT USE SOLVENTS THAT CONTAIN CHLORINE TO CLEAN THE EQUIPMENT
_______ (PUMP, HOSES, TANK AND FUNNEL) USED TO FILL THE IDG WITH OIL. CHLORINE CONTAMINATION OF THE OIL CAN CAUSE FAST DETERIORATION OF THE OIL AND WILL DECREASE THE LIFE OF THE IDG.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container 5.7 l (1.5 USgal) No specific warning notice No specific Torque Wrench : range 15.00 to 150.00 lbf.ft
(2.00 to 20.00 m.daN) DH13PM 1 TANK - ENGINE OIL FILLING UP
1EFF : ALL 1 24-21-00Page 328 1 1 Aug 01/05R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 03-002 GB DEF-STAN 91-101 LUBRICATING OIL TURBINE ENGINE SYNT BASE (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R 12-13-24-612-041 24-21-51-000-040 24-21-51-400-040 24-21-51-400-040 24-42-00-861-001 24-42-00-862-001 71-13-00-010-040 71-13-00-410-040 78-30-00-081-041 78-30-00-481-041 79-21-20-000-002 79-21-20-400-002 IDG Servicing - Filling of the IDG with Oil or Addition of Oil after a level CheckRemoval of the Integrated Drive Generator -IDG 1(2),(4000XU)Installation of the Integrated Drive Generator -IDG 1(2),(4000XU) Installation of the Integrated Drive Generator - IDG 1(2), (4000XU) (New EPGS)Energize the Ground Service Network from the External PowerDe-energize the Ground Service Network Supplied from the External PowerOpening of the Fan Cowl DoorsClosing of the Fan Cowl DoorsMake the Thrust Reverser Serviceable after MaintenanceMake the Thrust Reverser Unserviceable for MaintenanceRemoval of the Main Oil/Fuel Heat ExchangerInstallation of the Main Oil/Fuel Heat Exchanger
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
24-21-00-991-303 Fig. 303
R **ON A/C 401-499,
R 24-21-00-991-303-A Fig. 303A
R **ON A/C ALL
3. Job Set-up
__________
Subtask 24-21-00-861-056
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
Subtask 24-21-00-941-068
B. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice in position to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
On the overhead maintenance panel 50VU:
(a)
Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b)
Put a warning notice in position to tell persons not to energize the FADEC 1(2).
Subtask 24-21-00-010-074
C. Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
-
FOR 1000EM1
437AL, 438AR
-
FOR 1000EM2
447AL, 448AR
Subtask 24-21-00-481-053
D. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
4. Procedure_________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
(Ref. Fig. 303/TASK 24-21-00-991-303)
R **ON A/C 401-499,
R (Ref. Fig. 303A/TASK 24-21-00-991-303-A)
R **ON A/C ALL
Subtask 24-21-00-020-070
A. Removal of the IDG and the Main Oil/Fuel Heat Exchanger
(1) Remove the IDG (Ref. TASK 24-21-51-000-040).
(2) If the cause of contamination is a leak of the main oil/fuel heat exchanger:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ELECTRICAL POWER 电源1(54)
