• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-04-25 08:38来源:蓝天飞行翻译 作者:航空
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

NOTE: Do not touch cemented surface with dirty or oily fingers.
Neoprene Patch 1300L Cement 
- DeicerLeadStrap 
View A-A  Wooden Block or Bucking Bar May Be Used When NecessaryFor Support  NeoprenePatch CementedOver ExposedFabric 

Repairof Lead Strap
Figure 801


EFFECTIVITY:
PAGE
10/90

30-60-00 "Jan 11
PIPERAIRCRAFT
PA-42-720(AdvancedTrainer)
MAINTENANCEMANUAL

B. MaintenancePractices(continued)
11.DeicerBoots(continued)
(d) Removalof Deicers
(1.) Disconnectpropellerdeicerterminalsat studs on spinnerbulkheadandlip deicer terminalsatboot. (2.) UseMEKorToluoltosoftenadhesionlinebetweenbootandmountingsurface. (3.) Startingatonecomerof deicer, loosendeicerenoughtograspwithvisegrips pliers or
similartool.
(4.) Applysteadypull on deicerto pull it off mounting surface.ContinueusingMEKor Toluol to soften adhesionlines. Unless deicerisdamagedbeyondrepair,cushionjawsofpullingtoolto prevent damagetodeicersurface.Removeslowlyandcarefully.
(5.) RemoveresidualcementfrombladeusingTurco3 or equivalent.
(e) Preparationof SurfacePriorto Installationof Deicer
Preparepropellerbladesurfacefor proper deicerbootsinstallationas follows: PropellerBladeProtection (1.) Markand cut maskingtape samesizeas propellerdeicerincludingfirstinchof leadstrip(Figure401). (2.) Placemark at bladehubend in line with bladeleadingedge. (Location of markis determinedby sighting alongleadingedge.) Startingat hub,centertape on markand sticktape leadingedge. Markpositionof deicer lead strapwhereit crosses hub.
NOTE:Alldeicersonsinglepropellermust be equallydistantfrom hub or rational balance.
(3.) Removetape and paint in markedoff area down to baremetal. Clean area thoroughlywith MEKor acetone. Forfinalcleaning,wipesolventoff quicklywith clean,dry,lint-free clothto avoidleavingfilm.
CAUTION:  METALAND RUBBERPARTSMUSTBECLEANTO ASSURE MAXIMUM ADHESION.
(4.) Markcenterlineat propellerbladehubandon tape atoutboardedgeof marked area.
EFFECTIVITY:

12
PAGE 30-60-00
040-999

Jan10/903060-00
PIPER AIRCRAFT
PA-42-720 (Advanced Trainer)
MAINTENANCE MANUAL


B. MaintenancePractices(continued)
11. Deicer Boots (continued)
(e) Preparation of Surface Prior to Installation of Deicer (continued)
Center Line
r-Pattern
Masking Tape
PropellerDeicer Installation Figure401

EFFECTIVITY:
040-999
30-60-00 PAG 13
Jan 10/90

PIPER AIRCRAFT
PA-42-720(AdvancedTrainer)
MAINTENANCEMANUAL

B. MaintenancePractices(continued)
11.DeicerBoots (continued)
(f) Applicationof Cement
To apply cement on boots and mating surface, proceed as follows:
(1.) Mark centerline on glossy side of deicer with silver pencil.
(2.) Moisten clean cloth with MEK or acetone andclean unglazed surface of deicer, changing cloth frequently to avoid contamination
of clean area.

(3.) Thoroughly mix EC1300L or EC1403 cement and apply one even brush coat to unglazed back surface of deicer. Cement one inch of deicer lead strap. Allow to air dry for minimum1 hour at 40°F or above with relative humidity less than 70%. If humidity is 75% to 90%, allow 2 hours drying time. Do not apply cement if relative humidity is higher than 90%. Apply second even brush coat of cement.
NOTE: If deicer edges curl, apply masking tape to edges of glazed side before applying cementto unglazed side. Remove tape before installing deicer.
(4.) Apply even brush coat of EC1300L or EC1403 cementon cleaned surface of propeller blade immediately afterapplicationof second coat of cement of deicer. (Timing is importantas cement on both surfaces mustreach tack stage at same time.)
CHART 1 REQUIRED MATERIALS FOR REPAIR OF DEICERS
The materials and tools listed below are commercially available and are not supplied by B. F. Goodrich in kit form.
Item  Amount 
CementEC-1300L or EC-1403 (3M Mfg. Co.)  1 1/2 pt. for six blades 
Sealer A56B (B. F. Goodrich)  1 pt. for six blades 
Cleaning Solvent MEK (Methylethylketone) or Acetone 
B. F. Goodrich Filler 82-075A and B or 3M Sealer 
EC-801 and EC-1031 
B. F. Goodrich Sealer 82-076-1 and -2 or Lowe 
Brothers' paint C-19861, C21871 and C-16176 
Cleaning Cloth -any clean, lint-free cloth 
2 inch Rubber HandRoller 
1/4 inch Metal Hand Stitcher 
Scissors 
Turco #3 (Turco Products Co.)  1 1/2 pt. for six blades 
Masking Tape 

EFFECTIVITY: 040-999

Jan 10/90PAGE30-60-00
PIPER AIRCRAFT
PA-42-720 (Advanced Trainer)
MAINTENANCEMANUAL


B. MaintenancePractices (continued)
11. Deicer Boots (continued)
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:夏延飞机维护手册 Cheyenne IIIA PA-42-720 AMM 2(30)