**ON A/C ALL
Subtask 30-45-52-860-050
B. Aircraft Maintenance Configuration
(1) Make sure that the aircraft electrical circuits are energized (Ref. TASK 24-41-00-861-002).
(2) On the overhead control and indicating panel 21VU, make sure that the CAPT WIPER switch 5DB1 is set to OFF.
(3) On the overhead control and indicating panel 22VU, make sure that the F/O WIPER control switch 5DB2 is set to OFF.
(4) Make sure that the access platform is in position.
4. Procedure_________
Subtask 30-45-52-210-050
A. Make sure that the splines of the splined shaft are not damaged.
R R R NOTE : Apply a small quantity of COMMON GREASE (Material No. 04-004) or____ COMMON GREASE (Material No. 04-022) to the splined shaft before installation.
R R R NOTE : Do not mix Material No. 04-004 with Material No. 04-022. You can____ use Material No. 04-022 as an alternative to Material No. 04-004. Clean and degrease the parts before you use Material No. 04-022.
Subtask 30-45-52-420-050-A
B. Installation of the Wiper Arm (Ref. Fig. 401/TASK 30-45-52-991-001, 402/TASK 30-45-52-991-002)
(1) Install the wiper arm (8) on the splined shaft (5) and make sure that the wiper blade (1) is correctly installed (parking position).
(2) Make sure visually that the wiper blade (1), the wiper arm (8), the stops for the wiper blade in the parking position and the lift block are in the correct position. Make sure that the rubber of the wiper blade (1) is not worn.
Installation of Wiper Arm Figure 402/TASK 30-45-52-991-002
1EFF : 1 1R 1CES ALL 1 11 1 30-45-52 Page 408 Feb 01/99
(3)
When the wiper is in the parking position on the windshield, the lower edge of the rubber block (3) of the fitting that attaches the wiper blade (1) to the wiper arm (8) must be 3.5 +0.8 -0.8 mm (0.14 +0.03 -0.03 in.) from the windshield frame.
(4)
Install the screw (6) and TORQUE to 0.5 m.daN (44.24 lbf.in) and adjust the bolt (7).
(5)
If a roller (10) is installed on the wiper arm (8):
(a)
Turn the adjustment screw (9) until the roller support touches the wiper arm (8).
(b)
Make sure that after the adjustment, the roller (10) of the wiper arm (8) does not touch the windshield when the wiper blade (1) touches the windshield.
Subtask 30-45-52-820-050-A
C. Adjustment
(1) Adjustment of the wiper blade (1) pressure on the rest blocks (2) and (4): (Ref. Fig. 401/TASK 30-45-52-991-001)
(a) With an adjustable roller (10) installed on the wiper arm (8): 1 Put the wiper arm (8) in the center position on the
_
windshield.
2 Turn the adjustment screw (9) to get a minimum clearance of 1
_ mm (0.0393 in.) between the roller (10) and the windshield.
3 Put the wiper arm (8) in the parking position.
_
4 Make sure that the wiper blade (1) touches the rest blocks (2)
_
and (4).
a If there is no contact between the wiper blade (1) and the
_ rest blocks (2) and (4): correctly adjust the roller (10) to move it in the wiper arm (8) with the applicable value until the blade touches the rest blocks (2) and (4) without blade crash.
b If the wiper blade (1) is crashed on the rest blocks (2)
_ and (4), the adjustment of the roller (10) must not be changed after the adjustment of the clearance.
1EFF : ALL 1 30-45-52Page 409 1 1 Feb 01/05R 1 1 1CES 1
(b) With a roller (10) nstalled on the wiper arm (8):
1_ Adjust the blade pressure on the rest blocks (2) and (4) by
the adjusting screw (9) of the roller (10).
2_ Turn the adjustment screw (9) until the wiper arm (1) touches
the rest blocks (2) and (4) without blade crash.
(2) Adjustment of the force of the blade on the windshield: (Ref. Fig. 403/TASK 30-45-52-991-003)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ICE AND RAIN PROTECTION 防冰和排雨2(44)
