(2)
Close the access door 314AR.
(3)
Close the APU access doors 316AR, 315AL (Ref. TASK 52-41-00-410-001).
(4)
Remove the access platform(s).
(5)
Remove the warning notice(s).
Subtask 49-16-42-860-053
B. Aircraft Maintenance Configuration
(1) De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
FLAP - AIR INTAKE - REMOVAL/INSTALLATION
________________________________________
R **ON A/C 001-003, 051-099, 401-499,
TASK 49-16-43-000-001
Removal of the Air Intake Flap (GTCP 36-300)
1.
Reason for the Job
__________________
Self explanatory.
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action
52-41-00-010-001 Open the APU Doors for Access
49-16-43-991-001 Fig. 401
3. Job Set-up
__________ Subtask 49-16-43-860-055
A. Aircraft Maintenance Configuration
(1)
Put a warning notice on the panel 25VU to tell persons not to start the APU.
(2)
Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002).
(3)
De-pressurize the hydraulic systems (Ref. TASK 29-00-00-864-001). Subtask 49-16-43-865-050
B.
Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
Subtask 49-16-43-010-050-A
C. Get Access
(1)
Put the access platform in position below the APU compartment.
(2)
Open the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-010-001).
(3)
Set the LIGHT control switch 11LJ to the ON position.
4. Procedure
_________ (Ref. Fig. 401/TASK 49-16-43-991-001) Subtask 49-16-43-020-053
A. Removal of the Air Intake Flap
(1) Remove the actuator spindle (1) from the air intake flap (8). NOTE : Get access through the APU air intake in the fire wall at
____
FR80.
Air Intake Flap
Figure 401/TASK 49-16-43-991-001
CES
(a)
Remove and discard the cotter pin (3).
(b)
Remove the castle nut (4), the washer (5) the bolt (6) and disconnect the actuator spindle (1) from the air intake flap (8).
(2) Hold the air intake flap (8), remove the screws (7) and then the air intake flap (8) from the air inlet duct (2).
TASK 49-16-43-400-001
Installation of the Air Intake Flap (GTCP 36-300)
1. Reason for the Job
__________________
Self explanatory.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific access platform 3.5 m (11 ft. 6 in.)
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM 机载辅助动力 AIRBORNE AUXILIARY POWER3(12)
