(3)
Remove the circlip (1) and the cabin attendant work-lights (3).
R 1EFF : ALL 1 33-27-12Page 407 1 1 Aug 01/05 1 1 1CES 1
Cabin Attendant Work-Light.
Figure 401B/TASK 33-27-12-991-001-C
R 1EFF : 301-399, 1 33-27-12 Page 408
1 1 Aug 01/05
1 1
1CES 1
R Cabin Attendant Work-Light.
R Figure 401C/TASK 33-27-12-991-001-A
R 1EFF : 401-499, 1 33-27-12 Page 409
1 1 Aug 01/05
1 1
1CES 1
TASK 33-27-12-400-001 Installation of the Cabin Attendant Work-Lights NOTE : The installation procedure is the same for all cabin attendant
____ work-lights.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific stepladder 1 m (3 ft. 3 in.) 8PE004363-10 1 ADJUSTING DEVICE
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power
**ON A/C 001-049, 051-099, 101-149, 151-199, 211-299,
33-27-12-991-001 Fig. 401 **ON A/C 201-210,
33-27-12-991-001-B Fig. 401A **ON A/C 301-399,
33-27-12-991-001-C Fig. 401B
1EFF : ALL 1 33-27-12Page 410 1 1 Aug 01/05R 1 1 1CES 1
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R **ON A/C 401-499,
R 33-27-12-991-001-A **ON A/C ALL Fig. 401C
3. Job Set-up__________ Subtask 33-27-12-865-051
A. Make sure that this(these) circuit breaker(s) is(are) closed: -------------------------------------------------------------------------------PANEL SERVICE IDENT. LOCATION -------------------------------------------------------------------------------2000VU LIGHT - ATTND WORK 1LZ J03
4. Procedure_________ **ON A/C 001-049, 051-099, 101-149, 151-199, 211-299,
(Ref. Fig. 401/TASK 33-27-12-991-001) **ON A/C 201-210,
(Ref. Fig. 401A/TASK 33-27-12-991-001-B) **ON A/C 301-399,
R (Ref. Fig. 401B/TASK 33-27-12-991-001-C) **ON A/C 401-499,
R (Ref. Fig. 401C/TASK 33-27-12-991-001-A)
**ON A/C ALL
Subtask 33-27-12-860-050
A. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the stepladder is in position below the related panel.
(4) Make sure that the related circuit breaker panel is lowered. Subtask 33-27-12-420-050
B. Installation of the Cabin Attendant Work-Lights
CAUTION : DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS.
_______ THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP. IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
(1)
Install the cabin attendant work-lights (3) with the circlip (1).
(2)
Make sure that the electrical connectors are clean and in the correct condition.
(3)
Connect the electrical connectors (2) to the cabin attendant work-lights (3).
**ON A/C 001-049, 051-099, 101-149, 151-199, 201-299,
Subtask 33-27-12-410-052
C. Close Access
(1)
FOR 4LZ, 5LZ
(a) Close the circuit breaker panel 2000VU.
(2)
FOR 10LZ, 11LZ, 15LZ
(a) Close the circuit breaker panel 2001VU.
1EFF : ALL 1 33-27-12Page 412 1 1 Aug 01/05R 1 1 1CES 1
(3) FOR 14LZ
(a) Close and engage the combi panel 2042VU.
**ON A/C 301-399,
Subtask 33-27-12-410-052-B
C. Close Access
(1) FOR 204LZ, 205LZ
(a) Close the circuit breaker panel 2000VU.
(2) FOR 210LZ, 211LZ, 215LZ
(a) Close the circuit breaker panel 2001VU.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LIGHTS 灯光1(95)
