B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-002 USA MIL-P-8116 PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00)
R 1EFF : 106-149, 225-299, 301-399, 401-499, 1 33-37-11Page 418 1 1 Aug 01/05 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
33-37-00-710-001 Operational Test of the Wheel Well Lighting 33-37-11-991-003 Fig. 403 FOR FIN 7LL 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-00-410-001 Close the Main Gear Doors after Access FOR FIN 8LL 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-00-410-001 Close the Main Gear Doors after Access FOR FIN 9LL 32-12-00-010-001 Open the Main Gear Doors for Access FOR FIN 10LL 32-12-00-010-001 Open the Main Gear Doors for Access
3. Job Set-up
__________
Subtask 33-37-11-865-057
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU LIGHTING/WHL WELL/LTG/DOME 2LL X08
Subtask 33-37-11-860-051
B. Aircraft Maintenance Configuration
FOR 7LL
(1)
Make sure, that the access door 734 is open (Ref. TASK 32-12-00-010-001)
(2)
Make sure, that the ACCESS PLATFORM 2M (6 FT) is in position at zone 147 FOR 8LL
(3)
Make sure, that the access door 744 is open (Ref. TASK 32-12-00-010-001)
R 1EFF : 106-149, 225-299, 301-399, 401-499, 1 33-37-11Page 419 1 1 Aug 01/05 1 1 1CES 1
(4)
Make sure, that the ACCESS PLATFORM 2M (6 FT) is in position at zone 148 FOR 9LL
(5)
Make sure, that the access door 734 is open (Ref. TASK 32-12-00-010-001)
(6)
Make sure, that the ACCESS PLATFORM 2M (6 FT) is in position at zone 195 FOR 10LL
(7)
Make sure, that the access door 744 is open (Ref. TASK 32-12-00-010-001)
(8)
Make sure, that the ACCESS PLATFORM 2M (6 FT) is in position at zone 196
4. Procedure
_________
(Ref. Fig. 403/TASK 33-37-11-991-003) Subtask 33-37-11-420-052
A. Installation of the MLG Dome Light WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED
_______ BEFORE YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Remove the blanking caps from the electrical connectors.
(4)
Make sure that the electrical connectors are clean and in the correct condition.
(5)
Hold the MLG dome light (1) adjacent to its correct installation position.
(6)
Support the MLG dome light (1) and connect the electrical connectors
(2) and (3).
(7)
Apply the SPECIAL MATERIALS (Material No. 05-002) to the washers (5) and the screws (4).
R 1EFF : 106-149, 225-299, 301-399, 401-499, 1 33-37-11Page 420 1 1 Aug 01/05 1 1 1CES 1
(8) Install the MLG dome light (1) with the washers (5) and the screws (4).
(9) Tighten the screws (4). Subtask 33-37-11-865-058
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 2LL.
Subtask 33-37-11-710-052
C. Do the operational test of the wheel well lights (Ref. TASK 33-37-00-710-001).
5. Close-up
________ Subtask 33-37-11-410-052
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items. FOR 7LL
(2)
Close the access door 734 (Ref. TASK 32-12-00-410-001).
FOR 8LL
(3)
Close the access door 744 (Ref. TASK 32-12-00-410-001).
(4)
Remove the access platform(s).
R 1EFF : 106-149, 225-299, 301-399, 401-499, 1 33-37-11Page 421 1 1 Aug 01/05 1 1 1CES 1 EXTERIOR - DESCRIPTION AND OPERATION
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LIGHTS 灯光1(135)
