S 975-107
(9)
Collect the third set of samples:
(a)
Read the weight on each wheel from the scales and write the data in Figure 507, in the WHEEL WEIGHT, SAMPLE 3 column.
(b)
Read the counts for each load sensor with WBC mode-22 and write the data in Figure 508, in the SENSOR COUNTS, SAMPLE 3 column.
K. Decrease Body Strut Pressure
NOTE: In the steps that follow, you will decrease the pressure in the
____ shock struts of the body landing gear. You will not collect data.
S 865-147
CAUTION: DO NOT LET THE TOTAL WEIGHT ON THE NOSE WHEELS DECREASE BELOW
_______
10,000 LBS. THE AIRPLANE CAN TIP.
(1) Decrease the pressure in the shock struts of the body landing gear until the total weight on the nose wheels is between 10,000 and 10,500 lbs:
(a)
If restraining straps are used on the nose landing gear, make sure that they are not tight.
(b)
Decrease the pressure in increments of approximately 100 psi.
(c)
Make sure the pressure difference between the two shock struts of the body landing gear is always less than 50 psi.
S 865-050
(2) Stop for a minimum of 10 minutes to let the struts, WBS, and scales become stable.
L. Collect Data at Normal Strut Pressure - Third Time (Figures 509 and 510)
NOTE: In the steps that follow, you will increase the pressure in the
____ shock struts of the body landing gear to normal. Then you will collect scales data for Figure 509 and WBC data for Figure 510.
S 865-051
(1) Increase the pressure in the shock struts of the body landing gear to within 50 psi of the pressures written in Figure 502.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-41-00
ALL ú ú 05S Page 520 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
(2) S 865-052Stop for five minutes to let the strut pressures become stable.
(3) S 865-053Make sure that the shock strut pressures are within 50 psi of the pressures written in Figure 502.
(4) S 865-054Stop for five minutes again.
(5) S 975-117Collect the first set of samples: (a) Read the weight on each wheel from the scales and write the data in Figure 509, in the WHEEL WEIGHT, SAMPLE 1 column. (b) Read the counts for each load sensor with WBC mode 22 and write the data in Figure 510, in the SENSOR COUNTS, SAMPLE 1 column.
(6) S 865-056Stop for a minimum of one minute.
(7) S 975-121Collect the second set of samples: (a) Read the weight on each wheel from the scales and write the data in Figure 509, in the WHEEL WEIGHT, SAMPLE 2 column. (b) Read the counts for each load sensor with WBC mode-22 and write the data in Figure 510, in the SENSOR COUNTS, SAMPLE 2 column.
(8) S 865-058Stop for a minimum of one minute.
(9) S 975-123Collect the third set of samples: (a) Read the weight on each wheel from the scales and write the data in Figure 509, in the WHEEL WEIGHT, SAMPLE 3 column.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-41-00
ALL ú ú 05S Page 521 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
AXLE LOCA-TION WHEEL NO. WHEEL WHEEL WEIGHT (lbs.) FOR AXLE) (ADD AVERAGES Y (AXLE WEIGHT) V ING (WEIGHT-VALUE)
SAMPLE 1 SAMPLE 2 SAMPLE 3 AVERAGE
L WING FWD OUTBD 1 4
INBD 2
L WING AFT OUTBD 3 4
INBD 4
FWD L BODY OUTBD 5 4
INBD 6
AFT L BODY OUTBD 7 4
INBD 8
FWD R BODY INBD 9 4
OUTBD 10
AFT R BODY INBD 11 4
OUTBD 12
FWD R WING INBD 13 4
OUTBD 14
AFT R WING INBD 15 4
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 指示/记录系统 1(94)
