• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-04-12 10:00来源:蓝天飞行翻译 作者:航空
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者


 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-41-00
 ALL  ú ú 11S Page 558 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SENSOR LOCATION  SENSOR NO.  m = --éXYV 2éVX  é YVXVé é éV V 2éXV)( 
LEFT FWD  17F 
LEFT AFT  17R 
RIGHT FWD  18F 
RIGHT AFT  18R 

NOSE LANDING GEAR

Spans
Figure 523

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-41-00
 ALL  ú ú 10S Page 559 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F27032
A
747-400
MAINTENANCE MANUAL

SENSOR LOCATION  NO. SENSOR  SENSb =  -V+1 OR OFFSET (b) éYV méXV é 
LEFT FWD  17F 
LEFT AFT  17R 
RIGHT FWD  18F 
RIGHT AFT  18R 

NOSE LANDING GEAR

Offsets
Figure 524

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-41-00
 ALL  ú ú 10S Page 560 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F27033
A
747-400
MAINTENANCE MANUAL

LOAD SENSOR NUMBER  (mode 23) LOAD SENSOR RESISTANCE 
17F
 17R
 18F 
18R

Load Sensor Resistances
Figure 525

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-41-00
 ALL  ú ú 10S Page 561 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F27034
A
747-400 MAINTENANCE MANUAL
 (g)  
Push the + key to get the resistance values for the other sensors.

 (h)  
Push the RESET key to stop this mode. (The WBC shows PROCESS ABORTED.)


 O. Put Calibration Data into Calibration Module
 S 975-058
 (1)  Use WBC mode 99 to put the load sensor zeros, spans, offsets, and resistances from Figures 516, 523, 524, and 525 into the calibration module:
 (a)  Start mode 99 on the WBC: 1) Push the MODE key. 2) Push the 9 key two times. 3) Push the ENTER key. 4) When OK? shows, push the YES key. 5) When ENTER CAL CODE shows, push the decimal point (.) key,
 the 9 key, and then the MODE key. 6) Push the ENTER key. 7) When OK? .9M shows, push the YES key. 8) When ENTER 99 CODE shows, push the 7 key, the 4 key, and
 the 7 key. 9) Push the ENTER key. 10) When OK? 747 shows, push the YES key.
 (b)  Put in the zero values from Figure 516: 1) When EDIT ZERO? shows, push the Yes key. 2) Use the + key to step to the ZERO 17F display. 3) Put in the zero value for load sensor 17F from Figure 516.
 a) Use these keys to put in data: + - . 0-9
 b) Use the left arrow key to erase incorrect data.
 4) When the correct zero value shows, push the ENTER key.
 5) When OK? shows, make sure the value is correct and then
 push the YES key.
 6) When DONE? shows, push the NO key to go to the subsequent
 sensor.
 7) Put in the zero value for each sensor.
 8) When DONE? shows after you put in all the zero values,
 push the YES key. (The WBC then shows WRITE IN PROGRESS for approximately 8 seconds.) 9) When EXIT MODE 99? shows, push the NO key.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-41-00
 ALL  ú ú 10S Page 562 ú Jun 18/99
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:747-400 AMM 飞机维护手册 指示/记录系统 1(109)