3. Job Set-up
__________
Subtask 52-71-00-861-061
A. Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002)
Subtask 52-71-00-010-057
B. Get Access
(1)
Put an access platform in position at the applicable cargo compartment door 825 or 826.
(2)
Open the applicable cargo compartment door 825 or 826 to get access to the door threshold (Ref. TASK 52-30-00-860-002).
(3)
Remove the access panel(s) 825AR and/or 826AR to remove the handle flap.
(4)
Close the applicable cargo compartment door. NOTE : One person must be inside the cargo compartment to do the
____ adjustment test of the proximity switch.
Subtask 52-71-00-865-054
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU DOORS/CARGO 1MJ T12
1EFF : ALL 1 52-71-00Page 561 1 1 May 01/05 1 1 1CES 1
4. Procedure
_________ R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-71-00-820-055
A. Adjustment of the Proximity Switch
WARNING : DO NOT OPEN THE DOOR DURING THE ADJUSTMENT.
_______
(Ref. Fig. 508/TASK 52-71-00-991-008)
(1)
Make sure that the cargo compartment door is correctly locked with the locking handle in the recess of the handle flap.
(2)
Measure the clearance J2 between the target (1) and the proximity sensor (2).
-The clearance must be J2 1.8 -0.20 +0.20 mm (0.0708 -0.0078 +0.0078 in.).
(3)
If the clearance is not in the tolerances adjust as follows:
(a)
Disconnect the electrical connector (3) from the proximity switch (1).
(b)
Install blanking cap on the electrical connector (1).
(c)
Change the position of the proximity sensor (2) and the target
(1) as necessary.
(4) Connect the electrical connector (3) of the proximity switch (2). **ON A/C 051-052,
Subtask 52-71-00-820-055-A
A. Adjustment of the Proximity switch
WARNING : DO NOT OPEN THE DOOR DURING THE ADJUSTMENT.
_______
(Ref. Fig. 508A/TASK 52-71-00-991-008-A)
(1) Make sure that the cargo compartment door is correctly locked with the locking handle (5) in the recess of the handle flap (6).
1EFF : ALL 1 52-71-00Page 562 1 1 Aug 01/05 1 1 1CES 1
Proximity Switches (28WV and 34WV) - Locking Handle of the Cargo Compartment Figure 508/TASK 52-71-00-991-008
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-71-00Page 563 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1R Proximity Switches (28WV and 34WV) - Locking Handle of the Cargo Compartment R Doors R Figure 508A/TASK 52-71-00-991-008-A12 (SHEET 1)
R 1EFF : 051-052, 1 52-71-00Page 564 1 1 May 01/05 1 1 1CES 1R Proximity Switches (28WV and 34WV) - Locking Handle of the Cargo Compartment R Doors R Figure 508A/TASK 52-71-00-991-008-A22 (SHEET 2)
R 1EFF : 051-052, 1 52-71-00Page 565 1 1 May 01/05 1 1 1CES 1
R (2) Measure the clearance J2 between the target (8) and the proximity
R sensor (3).
R - The clearance must be J2 1.8 -0.25 +0.25 mm (0.0708 -0.0098 +0.0098
R in.).
R (3) If the clearance is not in the tolerances adjust as follows:
R (a) Remove the screws (4) from the handle flap (6) and the door
R structure.
R (b) Pull the locking handle (5) away from the recess of the handle
R flap (6) but keep the cargo compartment door locked.
R (c) Remove the handle flap (6) from the door structure (Ref. TASK 52-
R 31-21-000-002).
R (d) Disconnect the electrical connector (1) from the proximity switch
R (3).
R (e) Install blanking cap on the electrical connector (1).
R (f) Remove the bolts (2), the proximity switch (3) and the shim set
R (7) from the door structure.
R (g) Adjust the thickness of the shim set (7) until the clearance J2
R is correct.
R (h) Put the bolts (2) and the shim set (7) on the proximity switch
R (3).
R (i) Put the proximity switch (3) in position and install the bolts
R (2) and tighten them.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门8(14)
