EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-01
ALL ú ú 01 Page 203 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 022-054
(5)
Remove the squat sensor:
(a)
Loosen the coupling nut at the sensor end of the conduit assembly.
(b)
Remove the two bolts and the nuts that attach the sensor to the mounting bracket.
(c)
Carefully pull the sensor leads from the conduit and remove the line from sensor wires.
NOTE: Do not pull the line fully out of the conduit.
____
(d) Remove the sensor from the airplane.
TASK 32-61-01-402-067
3. Install the Nose Gear Squat Sensor (Fig. 201)__________________________________
A. Consumable Materials
(1)
D0000 Lubricant - BOE lube 50B50A
(2)
D00259 Enamel Primer - BMS 10-11, Type I
(3)
A00247 Sealant - Chromate BMS 5-95
(4)
B00184 Solvent - T-825 presealing, BMS 11-7
B.
References
(1)
AMM 09-11-00/201, Towing
(2)
AMM 32-00-30/201, Landing Gear Door Locks
(3)
AMM 32-09-02/201, Air/Ground Relay System
(4)
AMM 32-09-03/501, PSEU - Adjustment/Test
(5)
IPC 32-61-58 Fig. 1
(6)
WDM 32-51-11, Nose Gear Steering
C.
Access
(1)
Location Zone
715 Nose Landing Gear
D.
Prepare for the Installation
S 492-039
WARNING: MAKE SURE THE GROUND LOCKS AND THE STEERING LOCKOUT PIN ARE
_______ INSTALLED ON THE NOSE GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR OR TURN OF THE NOSE WHEEL CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1) Make sure the ground locks and steering lockout pin are installed on the nose landing gear (AMM 09-11-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-01
ALL ú ú 01 Page 204 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
E. Install the Squat Sensor
S 432-042
(1)
Do these steps to install the squat sensor:
(a)
Apply the lubricant to the sensor leads before you pull the leads through the conduit.
(b)
Attach the line that you kept in the conduit (during the removal) to the wires of the sensor.
(c)
Carefully pull the wires through the conduit into the P37 J-Box until the sensor is against the conduit end.
CAUTION:_______TIGHTEN THE SENSOR COUPLING NUT WITH YOUR HAND ONLY. IF YOU TIGHTEN THE SENSOR COUPLING NUT MORE TIGHTLY, IT CAN CAUSE DAMAGE TO THE SENSOR.
(d)
Apply the primer to the threads and install the coupling nut on the mounting bolts while the primer is wet.
(e)
Attach a lockwire to the sensor coupling nut.
(f)
Attach the sensor to the mounting bracket with the two bolts and nuts.
NOTE: Make sure you use the correct bolts and install the
____
bolts with the heads down.
(g)
Pull the sensor wires out through the P37 control panel.
(h)
Cut the wires to the correct length, if it is necessary.
(i)
Install the new terminal lugs on the sensor wires and connect the lugs to the terminal strip.
S 622-043
CAUTION:_______MAKE SURE YOU SEAL THE ELECTRICAL TERMINALS. IF YOU DO NOT SEAL THE TERMINALS, CONTAMINATION CAN GO INTO THE JUNCTION BOXES AND CAUSE DAMAGE TO THE SENSORS.
(2)
Seal the electrical terminals:
(a)
Clean the surface of the terminals with the solvent.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 起落架 LANDING GEAR 9(63)
