(2)
Make sure that the access panel/s is are removed (Ref. TASK 53-35-13-000-002).
R (a) FOR 15HH
-191KB.
R (b) FOR 35HH
-192KB.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 21-61-12Page 406 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
Subtask 21-61-12-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
R -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 15HH 122VU AIR COND/PACK TEMP/CTL SYS1/1/115VAC 1HH X22 122VU AIR COND/PACK TEMP/CTL SYS1/1/28VDC 3HH X21
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302,
R 122VU AIR COND/PACK TEMP CTL SYS2/1/28VDC 4HH Y19
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
R 122VU AIR COND/PACK TEMP CTL SYS2/1/115VAC 2HH Y18
R **ON A/C 106-149, 303-399,
R 122VU 4HH Y19
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
FOR 35HH 122VU AIR COND/PACK TEMP/CTL SYS1/2/115VAC 122VU AIR COND/PACK TEMP/CTL SYS1/2/28VDC 122VU AIR COND/PACK TEMP CTL SYS2/2/28VDC 122VU AIR COND/PACK TEMP CTL SYS2/2/115VAC 21HH 23HH 24HH 22HH W22W21Y21Y20
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 21-61-12Page 407 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 401/TASK 21-61-12-991-001)
Subtask 21-61-12-420-050
A. Installation of the Compressor Overheat-Temperature Sensor
(1)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(2)
Make sure that the removed packing (3) is in a good condition. If necessary replace the packing (3).
(3)
Remove the blanking plugs from the disconnected line ends.
(4)
Clean the component interface and/or the adjacent area.
(5)
Apply a small quantity of COMMON GREASE (Material No. 04-012) to the contact faces of the compressor overheat- temperature sensor (1) and to the packing (3).
(6)
Put the packing (3) in position on the compressor
overheat-temperature sensor (1).
(7)
Install the compressor overheat-temperature sensor (1) in the pipe assembly (4).
(8)
TORQUE the compressor overheat-temperature sensor (1) to between 0.5 and 1.0 m.daN (44.24 and 88.49 lbf.in).
(9)
Wipe clean the excess COMMON GREASE (Material No. 04-012) from the compressor overheat-temperature sensor (1) and safety with MISCELLANEOUS (Material No. 19-009).
(10)
Remove the blanking caps and connect the electrical connector (2).
(11)
Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 21-61-12-865-053
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
R (1) FOR 15HH
-1HH, 2HH, 3HH, 4HH.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 21-61-12Page 408 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
R (2) FOR 35HH - 21HH, 22HH, 23HH, 24HH:
Subtask 21-61-12-710-050
C. Do the operational test of the pack temperature-control system (Ref. TASK 21-61-00-710-001).
5. Close-up________
Subtask 21-61-12-410-051
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the access panel/s (Ref. TASK 53-35-13-400-002).
R (a) FOR 15HH - 191KB.
R (b) FOR 35HH - 192KB.
Subtask 21-61-12-862-050
B. De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 21-61-12Page 409 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
SENSOR - WATER EXTRACTOR TEMPERATURE (11HH,31HH) - REMOVAL/INSTALLATION
_______________________________________________________________________ TASK 21-61-13-000-001 Removal of the Water-Extractor Temperature Sensors 11HH and 31HH WARNING : MAKE SURE THAT AIR IS NOT SUPPLIED TO THE AIR CONDITIONING SYSTEM
_______ FROM THE MAIN ENGINE, THE APU OR A GROUND SOURCE. HOT COMPRESSED AIR CAN CAUSE INJURY TO PERSONNEL.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM AIR CONDITIONING 空调 5(20)
