曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
Station 259.50
D. Ground Spoiler Control Valve Adjustment
SUBTASK 27-62-00-860-014
(1) Do this task: Supply Electrical Power, TASK 24-22-00-860-811.
SUBTASK 27-62-00-860-015
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS,
ELEVATORS, FLAPS, SLATS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS
CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE
INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(2) Do this task: Speed Brake Hydraulic Systems A and B Pressurization,
TASK 27-62-00-800-801.
SUBTASK 27-62-00-210-002
(3) Examine the hydraulic connections on the ground spoiler control valve [51] for leakage.
SUBTASK 27-62-00-870-002
(4) Move the speed brake lever through more than one full cycle to bleed the hydraulic system.
SUBTASK 27-62-00-820-003
(5) Do the ground spoiler control valve [51] adjustment:
(a) Make sure the speed brake lever is in the DOWN position.
(b) Remove the bolt [52], washer [53] and nut [54] that attach the control rod [55] to the valve
lever [56].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-00
Page 521
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(c) Use digital protractor, STD-1232 to position the speed brake lever to 29 +/-2 degrees aft of
the DOWN position.
NOTE: 29 +/-2 degrees is equivalent to 2.78 +/-0.20 inches (70.6 +/- 5.1 mm) of the
speed brake lever travel from the DOWN position measured along the top surface
of the aisle stand light plate.
(d) By hand slowly move the valve lever [56] inboard until the inboard spoilers begin to move.
NOTE: The inboard spoilers will move before the outboard spoilers.
(e) Adjust the control rod [55]:
1) Loosen the checknut on the control rod [55].
2) Adjust the length of the control rod [55] until you can install the bolt [52].
3) Install the washer [53], nut [54] and bolt [52].
4) Make sure you can see the threads of the rod end through the inspection hole in the
control rod [55].
5) Tighten the checknut.
(f) Move the speed brake lever to the DOWN position.
(g) Slowly move the speed brake lever aft.
(h) Make sure the inboard spoilers begin to move at speed brake lever position of 29 +/-2
degrees aft of the DOWN position.
(i) Adjust the control rod [55] if necessary.
SUBTASK 27-62-00-860-016
(6) Do this task: Put the Speed Brake Hydraulic systems A and B Back to the Condition Before
the Pressurization, TASK 27-62-00-840-801.
SUBTASK 27-62-00-610-001
(7) Fill the hydraulic reservoir if it is necessary. To fill, do this task: Hydraulic Reservoir Servicing,
TASK 12-12-00-610-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-00
Page 522
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Ground Spoiler Control Valve Adjustment
Figure 503 (Sheet 1 of 2)/27-62-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-00
Page 523
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Ground Spoiler Control Valve Adjustment
Figure 503 (Sheet 2 of 2)/27-62-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-00
Page 524
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-62-00-820-803
6. Ground Spoiler Interlock Valve Adjustment
(Figure 504)
A. References
Reference Title
07-11-01-580-815 Lift the Airplane with the Jacks (P/B 201)
07-11-01-580-816 Lower the Airplane Off the Jacks (P/B 201)
27-62-61-400-805 Ground Spoiler Interlock Valve Functional Test - Jacking Method
(P/B 501)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1585 Kit - Rigging Pins, All Systems
(Part #: F70207-109, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
C. Location Zones
Zone Area
134 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Right
D. Ground Spoiler Interlock Valve Adjustment
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 飞机维护手册6 AIRCRAFT MAINTENANCE MANUA(63)
