曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
D. Prepare for the Test
SUBTASK 27-61-41-860-005
(1) Do this task: Supply Electrical Power, TASK 24-22-00-860-811.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-41
Page 411
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-61-41-860-006
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS,
ELEVATORS, FLAPS, SLATS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS
CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE
INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(2) Do this task: Speed Brake Hydraulic Systems A and B Pressurization,
TASK 27-62-00-800-801.
SUBTASK 27-61-41-480-001
(3) Install the mount, SPL-1670 and the control column assembly protractor, SPL-1680 on the
captain’s aileron control wheel.
SUBTASK 27-61-41-860-007
(4) Move the speed brake lever to the DOWN position.
SUBTASK 27-61-41-860-008
(5) Put the ailerons in the neutral position.
NOTE: The ailerons are in the neutral position when you can easily install the rig pin A/S-4
from the test set rig pin kit, SPL-1585 in the aileron bus drum.
(a) Remove the rig pin A/S-4.
SUBTASK 27-61-41-480-002
(6) Install the protractor, COM-1691 on the flight spoilers 2, 4, 8 and 10.
SUBTASK 27-61-41-820-002
(7) Adjust the protractor, COM-1691 to zero.
E. Spoiler Control Quadrant Test
SUBTASK 27-61-41-020-004
(1) Turn the captain’s aileron control wheel 87 degrees counterclockwise:
(a) Make sure that the spoiler No. 2 moves 32 +/-3 degrees up from the retracted position.
(b) Make sure that the spoiler No. 4 moves 37 +/-3 degrees up from the retracted position
SUBTASK 27-61-41-020-005
(2) Turn the captain’s aileron control wheel 87 degrees clockwise:
(a) Make sure that the spoiler No. 8 moves 37 +/-3 degrees up from the retracted position.
(b) Make sure that the spoiler No. 10 moves 32 +/-3 degrees up from the retracted position
SUBTASK 27-61-41-020-006
(3) Turn the wheel counterclockwise until the spoiler No. 8 starts to retract.
(a) Make sure the control wheel is a minimum of 70 degrees clockwise.
SUBTASK 27-61-41-020-007
(4) Turn the wheel clockwise until the spoiler No. 2 starts to retract.
(a) Make sure the control wheel is a minimum of 70 degrees counterclockwise.
SUBTASK 27-61-41-820-003
(5) Turn the captain’s aileron control wheel to the neutral position.
(a) Make sure the spoilers move to the retracted position.
SUBTASK 27-61-41-410-003
(6) Put the Airplane Back to Its Usual Condition
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-41
Page 412
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(a) Do this task: Put the Spoiler Hydraulic systems A and B Back to the Condition Before
the Pressurization, TASK 27-61-00-840-801.
(b) Remove the mount, SPL-1670 and the control column assembly protractor, SPL-1680 from
the captain’s aileron control wheel.
(c) Remove the protractor, COM-1691 from the spoilers No. 2, 4, 8 and 10.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-61-41
Page 413
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SPOILER CONTROL QUADRANT - INSPECTION/CHECK
1. General
A. This task supplies the data for a dimensional inspection of the spoiler control quadrant.
TASK 27-61-41-200-802
2. Spoiler Control Quadrant Inspection
(Figure 601)
A. General
(1) This procedure gives wear limits and repair data for the spoiler control quadrant.
B. Tools/Equipment
Reference Description
STD-1096 Micrometer - Depth, 0-1 Inch, Readable to 1/1000 Inch
STD-1097 Caliper - Vernier, 0-6 Inch, Readable to 1/1000 Inch
C. Location Zones
Zone Area
133 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Left
134 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Right
D. Procedure
SUBTASK 27-61-41-020-010
(1) To inspect the spoiler control quadrant, disconnect the aileron spring cartridge from the aileron
input crank.
SUBTASK 27-61-41-020-011
(2) Use these tools to check for wear on the parts of the spoiler control quadrant:
(a) micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096
(b) readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
737-600-700-800-900 飞机维护手册6 AIRCRAFT MAINTENANCE MANUA(47)
