S 024-068
(4)
Move the clevis end of the cable assembly thru the bracket.
S 024-069
(5)
In the lavatory, disconnect the cable from the quick-disconnect.
S 024-070
(6)
In the non-modular lavatory,
(a)
Help the cable end through the pulley.
(b)
Remove the locknut, washer and seal from the top side of the sleeve subassembly in the floor or drip pan.
S 024-071
(7) In the modular lavatory,
(a)
Remove the lockwire, locknut and washer from the upstream side of the sleeve subassembly on the toilet tank.
(b)
Pull the cable end out of the mounting bracket.
(c)
Remove the plate and gasket from the lavatory partition.
(d)
Remove the clamp that holds the cable assembly to the lavatory partition.
S 024-073
(8)
From under the lavatory, pull the cable assembly out of the lavatory.
(9)
Remove the top cable assembly from the airplane.
S 024-074
TASK 38-32-41-404-075
5. TOILET SYSTEMS WITHOUT THE BALL VALVE; Cable with Casing Installation (Fig. 401)______________________________
A. General
(1) Install the applicable insulation as necessary (AMM 25-21-39/401 and AMM 25-52-91/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
38-32-41
ALL ú ú 10 Page 411 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
B. Equipment and Materials
(1)
The Ball End of the Cable (use either of the following):
(a)
Part No. 24835, Teleflex Inc. (V78710)
(b)
MS20664C3
(2)
The Portable Swager - AT520J, ATI Industries (V00784)
(3)
Swaging Die - AT520CSB-3-332, Ball type ATI Industries (V00784)
C. Consumable Materials
(1) C00833 Sealant - BMS 5-108, Type 1, Class B-2 (AMM 20-30-11/201).
D. References
(1)
AMM 12-31-11/201, Body Section 41 Access Doors and Panels
(2)
AMM 20-30-11/201, Adhesives, Cements and Sealants
(3)
AMM 21-31-11/401, Cabin Pressurization Outflow Valve
(4)
AMM 25-21-39/401, Sidewall and Ceiling Insulation
(5)
AMM 25-52-91/401, Cargo Compartment Insulation
E. Access
(1) Location Zones
103 Forward Lavatory A
113 Aft Left Lavatory B
114 Aft Right Lavatory C
118 Aft Left Lavatory D
109 Aft Right Lavatory E
NOTE: Not all lavatories are installed on each airplane.
____
F. Prepare to Install the Cable Assembly
S 864-076
(1) Make sure the external locknut, washer and shim are removed from the service panel end of the cable assembly.
NOTE:____Some cable assemblies do not have the shims. Ignore the steps and parts of steps for the shims if they are not applicable.
S 824-077
(2)
Make sure the internal locknut is adjusted to a position that allows the shim and washer to be just inboard of the center of the threaded section. The threaded section is part of the slider housing.
S 824-078
(3)
For cable assemblies that will attach to a mounting bracket under the lavatory:
(a)
Make sure the top locknut and washer are not installed.
(b)
Make sure the bottom locknut and washer are adjusted to the position that allows the bottom washer to be just below the center of the threaded section.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
38-32-41
ALL ú ú 10 Page 412 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 824-079
(4) For cable assemblies that will have the sleeve subassembly attached to the lavatory floor or drip pan:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 WATER AND WASTE(73)
