S 865-006
(6) Remove electrical power if it is no longer necessary (AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
30-41-11
ALL ú ú 01 Page 502 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
WINDOW HEAT CONDUCTIVE COATING AND SENSOR - ADJUSTMENT/TEST
___________________________________________________________
1. General_______
A. This procedure contains two tasks:
(1)
A check of the electrical resistance of the windows
(2)
A check of the electrical resistance of the sensors in window No. 1 and window No. 2.
TASK 30-41-21-705-004
2. Do a Check of the Electrical Resistance of the Windows______________________________________________________
A. General
(1) The No.1, No.2, No.4 and No.5 windows have a layer of material on them that transmits electricity. This layer has an electrical resistance. With time the electrical resistance of this layer increases.
B. Standard Tools and Equipment
(1) Ohmmeter - 0- to 500-ohm range, accurate to | 5 percent
C. References
(1)
IPC 56-12-11
(2)
AMM 56-11-11/401, Window No.1
(3)
AMM 56-12-11/401, Window No.2
(4)
AMM 56-11-31/401
(5)
SSM 30-40-00, 30-41-00
(6)
WDM 30-41-11, 30-41-12
D. Access
(1) Location Zone
101 Control Cabin - Left
102 Control Cabin - Right
E. Procedure
S 865-002
(1) Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a) On the P6 panel, 1) R FRONT WINDOW ANTI-ICE 2) L FRONT WINDOW ANTI-ICE 3) R SIDE WINDOW ANTI-ICE 4) L SIDE WINDOW ANTI-ICE 5) RIGHT NO. 4 AND NO. 5 WINDOW ANTI-ICE 6) LEFT NO. 4 AND NO. 5 WINDOW ANTI-ICE
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
30-41-21
ALL ú ú 02 Page 501 ú Mar 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 725-001
(2) Do a test of the electrical resistance of Window No. 1 and window No. 2. (Fig.501)
NOTE: The No.1 and No.2 windows have bus bars located at the top
____ and bottom of the windows. The upper bus bar (power applied) have terminals at each upper corner. The lower bus bars (airplane ground) have terminals at each lower corner.
(a)
Disconnect the wires at the top of the No.1 window (window heat power connections).
(b)
Place an ohmmeter lead on an upper bus bar terminal and place other lead to airplane ground.
(c)
Make sure the resistance of the No. 1 window is as referenced in Table 1.
(d)
If the resistance check failed then replace the window. (AMM 56-11-11/401 No.1 window, AMM 56-11-12/401 No.2 window)
(e)
Make sure the No. 1 window is connected correctly to the back of the window heat control unit.
NOTE: See Table 1 for the correct connection to use for
____
the resistance you measure.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
30-41-21
ALL ú ú 03 Page 502 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(EXAMPLE, 4 LOCATIONS)
1.
DISCONNECT UPPER BUS BAR WIRES
2.
PLACE AN OHMMETER LEAD ON WINDOW BUS BAR TERMINAL AND PLACE OTHER LEAD TO AIRPLANE GROUND.
TEST WINDOW NO. 2 THE SAME AS WINDOW NO. 1.
Window No. 1 and No. 2 Resistance Test Figure 501
G89886
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 防冰和排雨(72)
