WTAI Solenoid Valve Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
30-11-13
ALL ú ú 02 Page 402 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
C90419
A 737-300/400/500MAINTENANCE MANUAL
S 034-007
(2)
Remove the electrical connector.
S 034-008
(3)
Remove the tube connections from the solenoid valve.
S 034-009
(4)
Remove the fasteners which attach the solenoid valve to the structure of the airplane.
S 024-010
(5)
Remove the solenoid valve.
S 034-011
(6)
Remove the tee from the solenoid valve.
(a) Discard the O-ring.
TASK 30-11-13-404-012
3. WTAI Solenoid Valve Installation (Fig. 401)
________________________________
A. References
(1) 36-05-00/201, Pneumatic System
B. Access
(1)
Location Zones
101/102 Control Cabin
507 Strut - Left Nacelle
607 Strut - Right Nacelle
(2)
Access Panels
5728/5828 Access Door Strut
C. Procedure
S 434-013
(1)
Install a new O-ring on the solenoid valve.
S 434-014
(2)
Install the tee in the solenoid valve.
(a) Do not tighten the tee.
(3)
Put the solenoid valve in the correct position.
(4)
Attach the valve to the structure.
S 434-015
S 424-016
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
30-11-13
ALL ú ú 02 Page 403 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 434-017
(5) Install the tubing B-nuts.
(a) Tighten the nuts.
S 434-018
(6)
Tighten the nut on the solenoid valve tee.
S 434-019
(7)
Install the ground strap to the bonding tab on the solenoid valve.
(a) Make sure the resistance from the solenoid body to the frame is not more that 0.0025 ohms.
S 434-020
(8)
Install the electrical connector.
S 724-021
(9)
Do the test for the solenoid valve.
(a)
Use the ground air source or the APU to pressurize the pneumatic system (Ref 36-05-00/201).
(b)
Examine the solenoid valve for leaks at the B-nuts and the tee connections. 1) No leakage is permitted.
D. Put the Airplane to Its Usual Condition
S 864-022
(1)
Remove the pressure from the pneumatic system if it is not necessary (Ref 36-05-00/201).
(2)
Close the access panel for the applicable engine.
S 414-023
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
30-11-13
ALL ú ú 01 Page 404 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
WING ANTI-ICING GROUND OVERHEAT THERMAL SWITCH -
________________________________________________ REMOVAL/INSTALLATION
____________________
1. General_______
A. This procedure has two tasks, one for the removal and one for the installation of the wing anti-ice ground overheat thermal switches (referred to as "thermal switches" in this procedure).
B. The thermal switches are located approximately 20 inches outboard of each wing anti-ice valve. You will get access to the thermal switches through the access panels on the lower surface near the wing leading edge.
TASK 30-11-21-024-006
2. Wing Anti-Icing Ground Overheat Thermal Switch Removal (Fig. 401)______________________________________________________
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 防冰和排雨(20)
