(2)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(3) Put the safety barriers in position.
**ON A/C 001-049, 051-061, 101-103, 201-203,
Subtask 57-20-00-010-055
B. Get Access
(1)
Put the access platform in position below zone 574(674).
(2)
Open the applicable access panels (Ref. AMM 064157 P. Block 1):
-
for the left wing, open 574AB, 574BB
-
for the right wing, open 674AB, 674BB.
R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
Subtask 57-20-00-010-055-A
B. Get Access
(1)
Put the access platform in position below zone 574(674).
(2)
Remove the applicable access panels (Ref. AMM 064157 P. Block 1):
-for the left wing, remove 574AB, 574BB
-for the right wing, remove 674AB, 674BB.
**ON A/C ALL
4. Procedure
_________ R (Ref. Fig. 608/TASK 57-20-00-991-007) Subtask 57-20-00-110-056
A. Preparation for Inspection
(1) Use a clean MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026), to clean:
-the joint plate on the aft face of the rear spar at RIB6.
Subtask 57-20-00-280-050
B. Inspection
(1) Do a special detailed inspection of the outer wing rear-spar aft-face spar joint plate at RIB6 (Ref. NTM 57-20-08 PART 9).
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the
____ correct repair procedure. If the defect is not included in this repair, you must request a procedure from Airbus Industrie.
Details of the Rear-Spar Aft-Face Spar Joint Plate - RIB6 R Figure 608/TASK 57-20-00-991-007
1EFF : ALL 1 57-20-00Page 642 1 1 Aug 01/05 1 1 1CES 1
5. Close-up
________
**ON A/C 001-049, 051-061, 101-103, 201-203,
Subtask 57-20-00-410-056
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the applicable access panels (Ref. AMM 064157 P. Block 1):
-for the left wing, close 574AB, 574BB
-for the right wing, close 674AB, 674BB. R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
Subtask 57-20-00-410-056-A
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels (Ref. AMM 064157 P. Block 1):
-for the left wing, install 574AB, 574BB
-for the right wing, install 674AB, 674BB.
**ON A/C ALL
Subtask 57-20-00-942-056
B. Removal of Equipment
(1)
Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and
standard tools and all other items.
1EFF : ALL 1 57-20-00Page 644 1 1 Aug 01/05R 1 1 1CES 1
TASK 57-20-00-200-007
Detailed Inspection of Outer Wing, Rear-Spar Forward-Face, Upper and Lower Root-Joint Fitting
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 572010-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific safety barriers
No specific warning notices
No specific access platform 2 m (6 ft. 7 in.)
98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
98D57004013000 2 HOOK-COVER (RIB 2 SURGE DOORS)
98D57004014000 2 HOOK-COVER (RIB2-SURGE DOORS)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼1(79)
