WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______
FALL CAN INJURE OR KILL YOU.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
CARBONFIBER REINFORCED PLASTIC.
1.
Reason for the Job
__________________
Refer to the MPD TASK: 551010-01
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific warning notices
No specific access platform 3.5 m (11 ft. 6 in.)
98D27903500000 4 PIN-SIDE STICK LOCKING
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System
29-10-00-864-002 Depressurize the Yellow Hydraulic System
29-10-00-864-003 Depressurize the Blue Hydraulic System
R SRM 551600 PB 101 55-16-00-991-001 Fig. 601
3. Job Set-up
__________
Subtask 55-16-00-860-050
A. Depressurize Hydraulic Systems
(1) Depressurize the Green, Yellow and Blue hydraulic systems (Ref. TASK 29-10-00-864-001) (Ref. TASK 29-10-00-864-002). (Ref. TASK 29-10-00-864-003)
Subtask 55-16-00-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16
Subtask 55-16-00-481-050
C. Install Locking Devices
(1) Put the PIN-SIDE STICK LOCKING (98D27903500000) in the CAPT and F/O side stick controllers.
Subtask 55-16-00-941-054
D. Safety Precautions
(1) Put the warning notices in the flight compartment to tell persons not to operate the flight controls.
(2) Put the warning notices in position to tell persons not to operate the hydraulic systems.
(3) Put the access platform in position at zone 314.
Subtask 55-16-00-010-050
E. Access
(1) Open the access door 314AR.
4. Procedure_________
(Ref. Fig. 601/TASK 55-16-00-991-001)
Subtask 55-16-00-210-050
R A. Detailed Inspection
R R R (1) Make a detailed inspection of the horizontal stabilizer rear support fittings, upper and lower attach fittings and surrounding external structure for: - delamination, - deterioration of the structure, - scratches, marks and dents, - cracks, - damaged paintwork. details.
R R R (2) If damage is found, look for allowable damage limits (Ref. SRM 551600 PB 101).
5. Close-up________
Subtask 55-16-00-410-053
A. Visual Inspection
(1) Make sure that the work area is clean and clear of tool(s) and other items.
THS Support Fittings
Figure 601/TASK 55-16-00-991-001
1EFF : ALL 1 55-16-00 Page 604
1 1 Feb 01/98
1 1
1CES 1
Subtask 55-16-00-410-050
B. Close Access
(1)
Close the access panel 314AR. Subtask 55-16-00-942-050
C. Remove Ground Equipment
(1) Remove the warning notice(s).
(2)
Remove the access platform(s). Subtask 55-16-00-081-050
D. Remove Locking Devices
(1) Remove the PIN-SIDE STICK LOCKING (98D27903500000) from the CAPT and F/O side stick controllers.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM STABILIZERS 安定面(35)