C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
55-33-13-010-002 Opening/Removal of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
55-33-13-410-002 Closing/Installation of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
R 55-34-11-000-001 Removal of the Vertical Stabilizer Tip R 55-34-11-400-001 Installation of the Vertical Stabilizer Tip 55-42-13-000-001 Removal of the Access Panel 326CT at the Rudder Attach Fitting No. 7 55-42-13-400-001 Installation of the Access Panel 326CT at the Rudder
Attach Fitting No. 7
ASRM 55-46-00-101 (for corrective action)
55-40-00-991-003 Fig. 603
3. Job Set-up
__________
Subtask 55-40-00-860-051
A. Aircraft Maintenance Configuration
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
(1)
Depressurize the Green, Yellow and Blue hydraulic systems (Ref. TASK 29-00-00-864-001).
(2)
Put the warning notices in the cockpit to tell persons not to operate the flight controls.
Subtask 55-40-00-865-060
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 49VU AUTO FLT/FAC1/28VDC 5CC1 B04 49VU AUTO FLT/FAC1/26VAC 14CC1 B03 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 16CE2 A02 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 105VU FLT CTL/SEC1/STBY SPLY 22CE B01 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU AUTO FLT/FAC2/26VAC 14CC2 M18 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
R **ON A/C 001-049, 051-099, 101-105, 151-158, 201-210,
Subtask 55-40-00-010-053
C. Get Access
(1)
Put the adjustable access platform in position at Zone 320.
(2)
Open and safety the access panel 325DL (Ref. TASK 55-33-13-010-002).
(3)
Remove the access panel 325EL (Ref. TASK 55-33-13-010-002).
(4)
Remove the vertical stabilizer tip 324AT (Ref. TASK 55-34-11-000-001).
R **ON A/C 106-149, 159-199, 211-299, 301-399, 401-499,
Subtask 55-40-00-010-053-A
C. Get Access
(1)
Put the adjustable access platform in position at Zone 320.
(2)
Open and safety the access panel 325DL (Ref. TASK 55-33-13-010-002).
(3)
Remove the access panel 325EL (Ref. TASK 55-33-13-010-002).
(4)
Remove the access panel 326CT at the rudder attach fitting No. 7 (Ref. TASK 55-42-13-000-001).
(5)
Remove the vertical stabilizer tip 324AT (Ref. TASK 55-34-11-000-001).
**ON A/C ALL
Subtask 55-40-00-110-051
D. Cleaning WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
MATERIAL.
THIS MATERIAL IS DANGEROUS.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Clean the inspection area with CLEANING AGENTS (Material No. 11-002) and a lint-free cloth.
4. Procedure
_________
(Ref. Fig. 603/TASK 55-40-00-991-003) 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM STABILIZERS 安定面(109)
