R THS Torque Box Internal Structure Outboard Fuselage Fairings Figure 602/TASK 55-10-00-991-002
1EFF : ALL 1 55-10-00Page 609 1 1 Feb 01/04 1 1 1CES 1R (2) If damage is found, look for allowable damage limits (Ref. SRM 551100 R PB 101).
5. Close-up
________
Subtask 55-10-00-410-053
A. Visual Inspection
(1) Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 55-10-00-410-051
B. Close Access
(1)
Install/close the trailing edge access panels. (Ref. TASK 55-13-11-400-001)
(2)
Install the THS leading edge (Ref. TASK 55-12-11-400-001).
(3)
Install the THS tips 332AB, 342AB. (Ref. TASK 55-14-11-400-001). Subtask 55-10-00-942-051
C. Remove Ground Equipment
(1) Remove the warning notice(s).
(2)
Remove the access platform(s).
Subtask 55-10-00-081-051
D. Remove Locking Devices
(1) Remove the PIN-SIDE STICK LOCKING from the CAPT and F/O side stick controllers.
Subtask 55-10-00-865-053
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3 TRIMMABLE HORIZONTAL STABILIZER - REMOVAL/INSTALLATION
______________________________________________________
TASK 55-10-11-000-001
Removal of the Trimmable Horizontal Stabilizer
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______ CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______ CARBONFIBER REINFORCED PLASTIC.
1. Reason for the Job__________________ Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific crane
No specific electrical blanking caps and plugs
No specific hydraulic blanking caps
No specific variable access platform
No specific warning notices
No specific NSA 9006-12B
No specific 35D55182822000
98D27903500000 2 PIN-SIDE STICK LOCKING
R 98D55109005000 2 SLING-THS
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-44-51-000-001 Removal of the Trimmable Horizontal Stabilizer (THS)
Actuator (9CE) 29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 49-11-11-000-001 Removal of the Auxiliary Power Unit (APU) - 4005KM
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM STABILIZERS 安定面(11)