(4)
Remove the ground support and maintenance equipment, the special and
standard tools and all other items.
RUDDER TIP - DESCRIPTION AND OPERATION
______________________________________
1. General_______ The rudder tip is the uppermost fairing of the rudder. It has the designation 326AT.
2. Component Location__________________ (Ref. Fig. 001)
R R R R 3. Description___________ The rudder tip is made of light alloy. It is fitted to the left and right side shells and the upper rib. Screws attach it. The rudder tip is also a lightning conductor. A retainer for a static discharger is installed on top of the tip.
Rudder Tip
Figure 001
1EFF : ALL 1 55-44-00 Page 2
1 1 Feb 01/98
1 1
1CES 1
RUDDER TIP - REMOVAL/INSTALLATION
_________________________________
TASK 55-44-11-000-001
Removal of the Rudder Tip
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific warning notice
No specific access platform 11 m (36 ft. 1 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
23-61-41-000-001 Removal of the Static Discharger 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 55-44-11-991-001 Fig. 401
3. Job Set-up
__________
Subtask 55-44-11-864-050
A. Make sure that the Green, Blue and /or Yellow hydraulic system is(are) depressurized and put it in the maintenance configuration (Ref. TASK 29-00-00-864-001).
Subtask 55-44-11-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 49VU AUTO FLT/FAC1/28VDC 49VU AUTO FLT/FAC1/26VAC 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 105VU FLT CTL/ELAC1/STBY SPLY 105VU FLT CTL/SEC1/STBY SPLY 121VU AUTO FLT/RUDDER/TRIM/IND 121VU AUTO FLT/FAC2/28VDC 121VU AUTO FLT/FAC2/26VAC 121VU FLIGHT CONTROLS/SEC3/SPLY 121VU FLIGHT CONTROLS/SEC2/SPLY 121VU FLIGHT CONTROLS/THS ACTR/MOT3 121VU FLIGHT CONTROLS/THS ACTR/MOT1 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE1 19CE2 21CE1 5CC1 14CC1 16CE2 16CE1 22CE 15CC 5CC2 14CC2 21CE3 21CE2 19CE3 19CE1 15CE2 B11B09B08B04B03A02A01B01M20M19M18Q19Q18Q17Q16R20
Subtask 55-44-11-941-050
C. Safety Precautions
(1) Put a warning notice in position in the cockpit to tell persons not to operate the flight controls.
(2) Put an access platform in position at Zone 360.
4. Procedure_________
Subtask 55-44-11-020-051
A. Remove the Rudder Tip (Ref. Fig. 401/TASK 55-44-11-991-001)
R (1) Carefully remove the sealant around the rudder tip.
R (2) Remove the screws (5), the washers (4) and the nuts (3).
R (3) Remove the screws (6) and the rudder tip (1).
R (4) Remove the static discharger (2) (Ref. TASK 23-61-41-000-001).
Rudder Tip
Figure 401/TASK 55-44-11-991-001
1EFF : ALL 1 55-44-11 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 55-44-11-400-001
Installation of the Rudder Tip
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM STABILIZERS 安定面(115)
