3. Job Set-up__________
R Subtask 55-40-00-010-051-A
R A. Get Access
R (1) Remove the rudder fairing 325AL (Ref. TASK 53-55-12-000-001).
R R (2) Open and safety the access panels 325DL, 325CL, 325BL (Ref. TASK 55-33-13-010-002).
R (3) Remove the access panel 325EL (Ref. TASK 55-33-13-010-002).
R R (4) Remove and discard the aluminum tape from the lightening holes in the front spar.
R (5) Remove the rudder tip 326AT (Ref. TASK 55-44-11-000-001).
4. Procedure_________
Subtask 55-40-00-210-052
A. Inspection
(1) Do a detailed visual inspection of the rudder side panels internal surfaces.
NOTE : If you find damage refer to (Ref. ASRM 55-41-00-101).____
5. Close-up________
R Subtask 55-40-00-410-051-A
R A. Close Access
R R (1) Make sure that the work area is clean and clear of tool(s) and other items.
R R (2) Cut and install the SPECIAL MATERIALS (Material No. 05-015C) over the lighting holes on the front spar.
R R (3) Apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001B) around the edge of the lighting hole covers.
R (4) Install the rudder tip 326AT (Ref. TASK 55-44-11-400-001).
R (5) Close the access panels 325DL, 325CL, 325BL (Ref. TASK 55-33-13-410-
R 002).
R (6) Install the access panel 325EL (Ref. TASK 55-33-13-410-002).
R (7) Install the rudder fairing 325AL (Ref. TASK 53-55-12-400-001).
R (8) Remove the warning notice(s).
R (9) Remove the access platform(s).
R (10) Remove the ground support and maintenance equipment, the special and
R standard tools and all other items.
TASK 55-40-00-210-004
Detailed Visual Inspection of the Rudder Attach Fittings 1, 2, 3, 4 and 5 and the Rudder Actuator Attach Fittings 1, 2 and 3
1. Reason for the Job
__________________
Refer to the MPD TASK: 554005-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific lint-free cloth
No specific warning notices
No specific adjustable access platform 12 m (39 ft. 4 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 11-002 USA MIL-PRF-680 DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT) (Ref. 20-31-00)
Material No. 15-005 AIB TN 10138 TYPE I GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 15-006 AIB TN 10138 TYPE I GRADE 3 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R R R R 29-00-00-864-001 55-33-13-010-002 55-33-13-410-002 ASRM 55-46-00-101 55-40-00-991-002 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action Opening/Removal of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR Closing/Installation of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR(for corrective action)Fig. 602
3. Job Set-up__________
Subtask 55-40-00-860-050
A. Aircraft Maintenance Configuration
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION_______ BEFORE YOU START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM STABILIZERS 安定面(107)
