-
FOR 2679GM
remove 22GG
-
FOR 2680GM
remove 21GG
-
FOR 2681GM
remove 19GG.
NOTE : When you remove the tachometers you will remove the tachometer
____
drives.
1EFF : ALL 1 32-42-68Page 402 1 1 Aug 01/04 1 1 1CES 1
TASK 32-42-68-400-003
Installation of the MLG Tachometer-Drive
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
R R Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-42-57-400-001 Installation of the Tachometer
3. Job Set-up
__________
Subtask 32-42-68-941-051
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
1EFF : ALL 1 32-42-68Page 403 1 1 Aug 01/04 1 1 1CES 1 1EFF : ALL 1 32-42-68Page 404 1 1 May 01/99 1 1 1CES 1 SLEEVES - AXLE WHEEL ADAPTOR (2631GM,2632GM,2633GM,2634GM)
R R R R (3) On the panel 400VU: - make sure that the landing-gear control-lever 6GA is in the DOWN position - make sure that the warning notice is in position to tell persons not to operate the landing gear.
4. Procedure_________
Subtask 32-42-68-420-050
A. Installation of the MLG Tachometer-Drive
(1) Install the applicable tachometers (Ref. TASK 32-42-57-400-001): - FOR 2681GM install 19GG - FOR 2679GM install 22GG - FOR 2680GM install 21GG - FOR 2678GM install 20GG.
NOTE : When you install the tachometers you will install the____ tachometer drives.
5. Close-up________
Subtask 32-42-68-942-050
A. Removal of Equipment
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Remove the safety barriers.
(3) Remove the warning notice(s).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
__________________________________________________________ REMOVAL/INSTALLATION
____________________
TASK 32-42-71-000-001
Removal of the MLG Axle Adaptor-Sleeves
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing Gears
32-41-11-000-006 Removal of the MLG Wheel
(2649GM,2650GM,2651GM,2652GM)
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
32-42-71-991-001-A Fig. 401
1EFF : ALL 1 32-42-71Page 401 1 1 Aug 01/05 1 1 1CES 1 -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架7(42)
