3. Job Set-up
__________ Subtask 32-42-36-941-059
A. Safety Precautions
(1)
Put the access platform in position at the applicable zone 571(671).
(2)
Put the safety barriers in position.
(3)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
(4)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear.
(5)
Put a warning notice in the cockpit, to tell persons not to pressurize the Green hydraulic system.
4. Procedure
_________ Subtask 32-42-36-870-058
A. Reactivation of the Normal-Brake Safety-Valve Assembly
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
WARNING : DO NOT LET OIL STAY ON YOUR SKIN FOR A LONG TIME AS IT CAN
_______
CAUSE INJURY.
CAUTION : MAKE SURE THAT THE FLUID DOES NOT STAY ON THE AIRCRAFT
_______ STRUCTURE. IF THE FLUID GETS ON THE AIRCRAFT STRUCTURE, WASH IT OFF IMMEDIATELY WITH SOAP AND WATER.
(1)
Depressurize the Green hydraulic system
(Ref. TASK 29-10-00-864-001).
(2)
Depressurize the reservoir of the Green hydraulic system. (Ref. TASK 29-14-00-614-001).
(3)
Bleed the normal brake system (Ref. TASK 32-42-00-870-001).
R 1EFF : 001-002, 051-052, 1 32-42-36Page 308 1 1 May 01/05 1 1 1CES 1 Subtask 32-42-36-710-055
B. Test
(1) Do an operational test of the normal braking system (Ref. TASK 32-42-00-710-001).
5. Close-up
________ Subtask 32-42-36-942-056
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 001-002, 051-052, 1 32-42-36Page 309 1 1 May 01/05 1 1 1CES 1
R R Normal-Brake Safety-Valve Figure 302/TASK 32-42-36-991-004
1EFF : 1 1 1CES ALL 1 111 32-42-36 Page 310 Nov 01/04
SAFETY VALVE - NORM BRAKE (2616GM,2617GM,2618GM,2619GM) - REMOVAL/INSTALLATION
______________________________________________________________________________
TASK 32-42-36-000-001
Removal of the Normal Brake Safety-Valve 2618GM(2617GM), 2616GM(2619GM)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps No specific circuit breaker(s) safety clip(s) No specific plastic bag No specific safety barriers No specific warning notice No specific warning notices No specific container 1 l (0.2641 USgal) No specific access platform 2.5 m (8 ft. 2 in.)
1EFF : ALL 1 32-42-36Page 401 1 1 Nov 01/04R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears
R **ON A/C 001-002, 051-052,
32-42-36-991-001 Fig. 401
**ON A/C ALL
R Post SB 32-1190 For A/C 001-002,051-052,
32-42-36-991-005 Fig. 402
**ON A/C ALL
3. Job Set-up
__________
Subtask 32-42-36-941-054
A. Safety Precautions
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架7(28)
