(4) Remove the ground support and maintenance equipment, the special and
standard tools and all other items.
1EFF : ALL 1 28-12-00Page 613 1 1 May 01/04 1 1 1CES 1 1EFF : ALL 1 28-12-00Page 614 1 1 Feb 01/05 1 1 1CES 1 1EFF : ALL 1 28-12-00Page 615 1 1 Feb 01/05 1 1 1CES 1
R TASK 28-12-00-210-001
R Visual Check of Vent Surge Tank Burst Disc (EXTERNAL)
R WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______
R START A TASK ON OR NEAR:
R - THE FLIGHT CONTROLS
R - THE FLIGHT CONTROL SURFACES
R - THE LANDING GEAR AND THE RELATED DOORS
R - COMPONENTS THAT MOVE.
R WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______
R GEAR.
R 1. Reason for the Job__________________
R Refer to the MPD TASK: 281200-01
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific safety barriers
R No specific warning notices
R No specific access panel 2.5 m (8 ft. 2 in.)
R 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
R B. Referenced Information
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 28-12-41-000-001 Removal of the Overpressure Protector 46QM (47QM)
R 28-12-41-400-001 Installation of the Overpressure Protector 46QM
R (47QM)
R 28-12-00-991-020 Fig. 603
R 3. Job Set-up__________
R Subtask 28-12-00-941-061
R A. Safety Precautions
R (1) Put the safety barriers in position.
R (2) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001)
R on the flap/slat control lever.
R (3) Put warning notices in the cockpit to tell persons not to operate the
R flaps or slats.
R (4) Put an access panel in position below the applicable zone 550 or 650.
R 4. Procedure_________
R Subtask 28-12-00-210-061
R A. Visual Check of the Vent Surge Tank Burst Disc (EXTERNAL)
R (Ref. Fig. 603/TASK 28-12-00-991-020)
R (1) Inspect the burst (safety) disc through the opening in access panel
R 550CB(650CB). Make sure that:
R - the white cross on the burst (safety) disc can be clearly seen
R - the burst (safety) disc is in one piece.
R (2) If the burst (safety) disc is damaged, replace the overpressure
R protector assembly (Ref. TASK 28-12-41-000-001) (Ref. TASK 28-12-41-
R 400-001).
R 5. Close-up________
R Subtask 28-12-00-942-064
R A. Removal of Equipment
R (1) Remove the safety barriers.
R (2) Remove the warning notice(s).
R (3) Remove the access platform(s).
R (4) Remove the ground support and maintenance equipment, the special and
R standard tools and all other items.
R R Vent Surge Tank Burst Disc - Location and Detail Figure 603/TASK 28-12-00-991-020
1EFF : 1 1 1CES ALL 1 111 28-12-00 Page 616 Feb 01/05
R PROTECTOR - OVERPRESSURE (46QM,47QM,96QM,102QM,103QM) - REMOVAL/INSTALLATION
____________________________________________________________________________ TASK 28-12-41-000-001 Removal of the Overpressure Protector 46QM (47QM) WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUEL 燃油1(167)
