S 166-059
(2)
Examine the external leak area regularly for one hour.
NOTE: You can monitor the leak area for a longer time to make
____ sure the leak area is OK. If the leak was a stain or a seep, it can be necessary to monitor the leak area for a longer time to make sure you repaired the leak.
S 796-060
(3) If you repaired a fastener, you can use the vacuum cup, ST8744, (Fig. 611) to make sure it does not have a leak.
(a)
Attach a vacuum source (10 psi, 69 kPa) to the vacuum cup.
(b)
Put the vacuum cup on the fastener that you repaired.
(c)
Apply the vacuum pressure (10 psi, 69 kPa).
(d)
If no bubbles or other leak indications occur, you repaired the fastener correctly.
S 166-061
(4) Make sure there are no fuel leaks.
NOTE: Make sure the leakage area is maintained, at a minimum
____ to the leakage limits shown in Figure 603 after the 1 hour inspection.
S 396-062
(5)
If you removed aerodynamic smoother to find the external leak, repair the hole (AMM/51-31-00/201).
S 416-032
(6)
If you removed some skin panels to get access to the external leaks, install them again.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-11-00
ALL ú ú 01 Page 613 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
TASK 28-11-00-796-063
3. Alternative Procedures for Fuel Tank Leak Detection
___________________________________________________
A. General
(1)
The best leak detection procedure is usually to find the leak externally with talcum powder and then to find the internal leak with the air pressure and soap bubble procedure ("backblowing"). That procedure is given in the above task: Leak Detection and Repair.
(2)
This task contains alternative procedures used to find a leak. These procedures can be used if backblowing is not possible, or if it fails to show all of the leaks. This task also contains the internal pressure and bubble procedure which can be used to find external leak locations after an airplane is defueled. These are the procedures:
(a)
Pressure Box Application
(b)
Dye Injection Procedure
(c)
Internal Pressure and Bubble Procedure
(d)
The hollow bolt procedure (for use in areas of complex structure)
(e)
The hollow bolt and dye injection procedure.
(3)
Before you defuel a fuel tank which has a leak, try to find all of the leaks in the fuel tank. Repair all leaks each time a fuel tank is defueled to repair leaks.
B. Equipment
(1)
Testing Device - P/N F71329
(2)
Pressure box (fabricated) (Fig. 612)
(3)
Air supply - 0 to 10 psig (0 to 69 kPa)
CAUTION: ATTACH RED COTTON WEBBING STREAMERS TO ALL PLUGS AND CLOSURE
_______ ITEMS USED IN THE TANKS. THE PLUGS AND CLOSURE ITEMS CAN CAUSE DAMAGE TO EQUIPMENT IF YOU DO NOT REMOVE THEM BEFORE FLIGHT.
(4)
Closure plugs and cover items
(a)
One Structural Vent Plug - F80080-100
(b)
One Vent Scoop Closure Plug - F80080-88
(c)
One Surge Tank Drain Tube Plug Assembly - F80080-55
(d)
Two Drain Check Valve Plugs - F80080-112
(e)
One Float Valve Closure Plug - F80080-8
(f)
Two Tube Plug Assemblies - F80080-49
(g)
One Structural Vent Cover Assembly - F80080-56
(5)
Surge Tank Pressure Door Assembly - F80080-82 or F80080-5
(6)
Center Wing Tank Pressure Test Door - F80148-1 or F80172-1
(7)
Water Safety Relief Manometer - F72951-1 (Fig. 615)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-11-00
ALL ú ú 01 Page 614 ú Mar 12/02
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 燃油 FUEL 1(49)
