(1)
Clean the cable (9) with CLEANING AGENTS (Material No. 11-004).
(2)
Apply COMMON GREASE (Material No. 04-004) to the cable (9).
4. Procedure
_________
(Ref. Fig. 401/TASK 38-14-49-991-004) Subtask 38-14-49-420-051
A. Install the Control Cable
(1)
Do an inspection of the component interface and/or the adjacent area.
(2)
Put the swivel ends (12) in position.
(3)
Install the washers (13) and the nuts (14).
(4)
Put the rigid sleeve (15) in position.
(5)
Install the hollow hex head screws (16) in the swivel ends (12) but do not tighten at this stage.
(6)
Install the cable (9) in the rigid sleeve (15).
(7)
At the control handle lever:
(a)
Install the locknut (10) and the clevis (11) on the cable (9), but do not tighten at this stage.
(b)
Put the clevis (11) in position until you can install the pin (6).
(c)
Install the pin (6), the washer (5) and the new cotter pin (4) on the clevis (11).
(d)
Tigthen the locknut (10) and safety it with 0.8 mm lockwire.
(8)
Tighten the hollow hex head screws (16) in the swivel ends (12).
(9) Install the sliding end (8) counter clockwise on the cable (9). Subtask 38-14-49-820-050
B. Adjust the Control Cable
(1)
In the drain panel, make sure that the control handle is in SHUT position.
(2)
Hold the lever of the drain valve 4MP in the SHUT position.
(3)
Adjust the sliding end (8) in position until you can install the pin
(6).
(4)
Make sure that you can feel or see the cable (9) through the inspection hole in the sliding end (8).
Subtask 38-14-49-420-054
C. Install the Clevis to the Drain Valve
(1)
Install the pin (6), the washer (5) and the new cotter pin (4).
(2)
Tighten the nut (7).
(3)
Install the clamps (3), the washers (2) and the nuts (1) and tighten them.
(4)
Install the tie-down strap (17).
(5)
Install the lead-bonding (20). NOTE : If removed put the insulation sleeve in position.
____ Subtask 38-14-49-680-056
D. Preparation for the Test
(1) If necessary, fill the potable water tank (Ref. TASK 12-15-38-613-001).
(2) Pressurize the system water potable (Ref. TASK 38-10-00-614-001). Subtask 38-14-49-865-055
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1PX Subtask 38-14-49-710-051
F. Do this Test
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the drain panel:
-Make sure that the drain valve 4MP is in the SHUT position.
-Turn the control handle of the drain valve 4MP in the OPEN position.
-Put back the control handle of the 4MP in the SHUT position.
2. On the CTL PNL-WATER QTY IND 2023VU:
-Put the control handle in the DRAIN position.
-Push the control handle. Make sure that the control handle comes back to the NORMAL position.
5. Close-up
________
Subtask 38-14-49-410-051
A. Close AccessOn the drain panel:
-
Make sure that the drain valvecontrol light 2MP is OFF.
-
Make sure that the drain valvecontrol light 2MP is ON.
-
Make sure that the drain valvecontrol light 2MP is OFF.
On the drain valve:
-
Make sure that the drain valvecontrol light 2MP is ON.
NOTE : Do not take into account the
____ others indication.
-Make sure that the drain valvecontrol light 2MP is OFF.
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the passenger/crew door 832 or 842 (Ref. TASK 52-10-00-410-001).
(3)
Close the drain panel 133AL.
1EFF : ALL 1 38-14-49Page 411 1 1 Nov 01/00R 1 1 1CES 1
(4) Close the access door 171AL of the service panel 2023VU.
(5) In the FWD cargo-compartment, install the sidewall panel 131HW and R the floor panels 131EF, 131FF, 131GF.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WATER/WASTE 1(101)
