OVERHEAD STOWAGE COMPARTMENT - REMOVAL/INSTALLATION
EFFECTIVITY
Wide-Body Look Interior
1. Remove Overhead Stowage Compartment
A. Pull inboard on compartment latch handle and open stowage compartment.
B. Disconnect fabric portion of shroud from outboard edge of stowage compartment by removing two attaching screws (Fig. 401).
C. Open adjacent stowage compartment to gain access to attachments for the snubber.
D. Support compartment and disconnect snubber from bracket on structure by removing attaching bolt, spacers, washers, and nut.
E. If removing one of the long (40 inches) stowage compartments, remove screw, spacer, washer and nut attaching limiting cable to stowage compartment.
F. Support compartment, pull hinge lock inboard at each end of compartment, and move compartment inboard to remove.
2. Install Overhead Stowage Compartment
A. Pull hinge lock inboard at each end of compartment and move compartment outboard to engage hinge fittings with support pins on structure (Fig. 401).
B. Release hinge locks and check that compartment is locked to both support pins.
C. If installing one of the long (40 inches) stowage compartments, attach limiting cable to compartment with screw, spacer, washer, and nut.
D. Attach snubber to bracket on structure with attaching bolt, spacers, washers and nut.
NOTE: In some areas this bolt also attaches the limiting cable of the adjacent stowage compartment.
E. Connect fabric portion of shroud to outboard edge of stowage compartment with two attaching screws.
F. Close stowage compartment and any adjacent stowage compartment opened for access to attachments.
Aug 15/78 25-24-311 Page 401
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
Overhead Stowage Compartment Installation 545
25-24-311 Figure 401 (Sheet 1) Aug 1/74
Page 402
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
545 Overhead Stowage Compartment Installation
Aug 01/74 Figure 401 (Sheet 2) 25-24-311
Page 403
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
Overhead Stowage Compartment Installation 532
25-24-311 Figure 401 (Sheet 3) Aug 1/74
Page 404
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
533 Overhead Stowage Compartment Removal/Installation Sequence
Aug 01/74 Figure 402 25-24-311
Page 405
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
E. If removing 40-inch compartment, disconnect limiting cable at opposite end.
F. Support compartment, pull hinge lock inboard at each end of compartment, and move compartment inboard to remove (Detail B, Fig. 401).
3. Install Overhead Stowage Compartment (Fig. 401)
A. Position compartment hinge fittings over support pins (detail B).
B. Support compartment, pull hinge lock at each end of compartment inboard and move compartment outboard to engage support pins in hinge fittings. Release hinge lock fittings and check support pins and hinge fitting engagement.
C. Connect snubber upper end fitting (detail A).
NOTE: When 40-inch compartment is adjacent, also connect limiting cable where required.
(1)
On snubbers retained by bolt, install bolt, nut, washers and spacers.
(2)
On snubber retained by spring-loaded pin, push in on pin, with blunt small diameter tool, until snubber end fitting can be inserted between the attachment bracket flanges and trap pin.
(3)
Remove tool and push in on end fitting until pin retains end fitting.
D. If installing 40-inch compartment, connect limiting cable at opposite end.
E. Install screws to connect fabric closure panel to compartment.
F. Close compartment and check compartment is securely latched. If compartment fails to latch, check adjustment of latch strikers.
CAUTION: DO NOT SLAM COMPARTMENTS SHUT. CLOSE GENTLY USING HAND PRESSURE ADJACENT TO LATCH HANDLE ONLY, TO PREVENT DAMAGE AND/OR LATCH STRIKER MALADJUSTMENT.
533
25-24-311 Page 406 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Aug 1/74
OVERHEAD STOWAGE COMPARTMENT - ADJUSTMENT/TEST
EFFECTIVITY
Wide-Body Look Interior
1. Overhead Stowage Compartment Adjustment
A. General
(1)
The following procedure is applicable for adjustment of the overhead stowage bin latch, if any component of the latch mechanism is replaced or a latch malfunctions.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737 AMM 飞机维护手册 EQUIPMENT/FURNISHINGS(89)
