(2)
Check security of anchor.
500
May 15/67 25-61-200
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Page 601
ESCAPE SLIDE ASSEMBLY (DOOR-MOUNTED) - DESCRIPTION AND OPERATION
1. General
A. Each escape slide assembly consists of an escape slide package, an escape slide compartment and two floor brackets. Escape slide package is stowed in escape slide compartment fastened to lower inboard face of forward entry door, forward service door and aft service door. Floor brackets are located at forward and aft ends of doorways inboard of door sill.
B. Escape slide package consists of an escape slide, a detachable girt, a girt bar, an air bottle and a valise. Air bottle holds high-pressure gas for inflating slide. Valise holds slide in its folded (stowed) position, which opens to free and deploy slide.
C. Escape slide detachable girt and a mooring line enables use of slide as a supplementary floatation device after airplane ditching. Separation of slide from girt is accomplished by lifting a flap and pulling on ditching handle. Detachable girt may be replaced (when damaged or soiled) without complete repacking of slide.
2. Operation (Fig. 1)
A. Escape slide girt bar is stowed in retainers on compartment cover. When it is desired to use slide, girt bar is removed from retainers and installed in floor brackets. Opening door will then pull escape slide package out of compartment. Escape slide inflates automatically as slide deploys. A manual inflation handle is furnished, which can be used if automatic inflation system should fail.
566
Nov 15/77 25-61-300
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Page 1
Escape Slide Operation 540
25-61-300 Figure 1 (Sheet 1) May 01/74
Page 2
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
540 Escape Slide Operation
May 01/74 Figure 1 (Sheet 2) 25-61-300
Page 3
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
ESCAPE SLIDE ASSEMBLY (DOOR-MOUNTED) - MAINTENANCE PRACTICES
1. General
A. The escape slide assembly consists of an escape slide compartment and an escape slide package in the compartment. Escape slide floor brackets are excluded from this procedure (Ref 25-61-332).
B. This section provides instructions for removing and installing the escape slide assembly from the door (par. 2 and 3), removing and installing the escape slide package (par. 4 and 5), escape slide package inspection (par. 6), escape slide package check (par. 7) and escape slide assembly restoration (par. 8).
2. Remove Escape Slide Assembly From Door (Fig. 201)
A. Unlock two quarter-turn fasteners or remove attach screws.
B. Rotate top of compartment inboard slightly to clear door.
C. Lift compartment to disengage fitting from lower support bracket.
3. Install Escape Slide Assembly To Door (Fig. 201)
NOTE: Escape slide compartments for forward doors are not the same as those for aft doors. An aft door compartment can be identified by the following statement stenciled in red letters on its outboard side: FOR USE ON AFT SERVICE AND ENTRY DOORS ONLY. The outboard side of a forward door compartment has no markings.
A. Set fitting in lower support bracket.
B. Rotate top of compartment outboard.
C. Align slide and engage quarter-turn fasteners or install attach screws.
4. Remove Escape Slide Package (Fig. 201)
CAUTION: ESCAPE SLIDE PACKAGE SHOULD BE HANDLED ONLY ON A CLEAN SURFACE. CARE SHOULD BE TAKEN NOT TO PUNCTURE OR ACCIDENTALLY INFLATE SLIDE.
A. Remove escape slide assembly from door (Ref par. 2).
B. Lay escape slide assembly on floor or other horizontal surface.
C. Remove girt bar from retainers.
D. Check girt bar for pitting and/or corrosion (Ref par. 6).
E. Pull latch cable to open compartment latch.
F. On slides with spring clamp girt bar attachment, remove latch assembly (if required).
(1)
Remove nut, screw and spacer (not on all airplanes) that fasten latch cable to spring clamp and remove latch assembly and cable.
(2)
Remove spring clamp from girt bar.
(3)
On slide installations without spacer, attach spring clamp to latch cable using screw and nut.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737 AMM 飞机维护手册 EQUIPMENT/FURNISHINGS(144)
