Aft Windscreen Installation 505
25-24-144Page 402 Figure 401 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Oct 20/84
CARGO/PASSENGER DIVIDING PARTITION - REMOVAL/INSTALLATION
1. General
A. A partition is used to divide the cargo from the passenger compartments in any of the combined passenger/cargo configurations. The partition is provided with a sliding door for personnel passage.
2. Remove Cargo/Passenger Dividing Partition (Fig. 401)
A. Withdraw hanger pins on upper center (decompression) panel and remove panel.
B. Withdraw pins from upper beam and remove beam segments.
C. Withdraw two hanger pins along left side of center panel and one at lower right corner of panel. Remove panel.
D. Withdraw hanger pins from lower beam at bottom of left panel and move panel inboard to clear outboard support arm. Remove panel.
CAUTION: DO NOT MOVE INBOARD END OF PANEL FORWARD OR AFT UNTIL CLEAR OF OUTBOARD SUPPORT ARM TO PREVENT DAMAGE TO SOCKET.
F. Pull up on spring loaded pins on track attach fittings and move beam assembly forward or aft until fittings can be lifted from track. Remove beams.
G. If required, remove outboard support arms from air conditioning outlet extrusion by removing screws.
H. Reassemble outboard support arms to prevent loss of parts.
576
Nov 15/79 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 25-24-152 Page 401
K92372 K92373 K92374
Cargo/Passenger Dividing Partition Installation 576
25-24-152 Figure 401 (Sheet 1) Nov 15/79
Page 402
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
506 Cargo/Passenger Dividing Partition Installation
May 01/75 Figure 401 (Sheet 2) 25-24-152
Page 403
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
Cargo/Passenger Dividing Partition Installation 506
25-24-152 Figure 401 (Sheet 3) May 01/75
Page 404
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
3. Install Cargo/Passenger Dividing Partition (Fig. 401)
A. If removed, install outboard support arms on air conditioning outlet extrusion in approximate location. Do not tighten screws.
B. Hold spring loaded pins on track attach fittings in up position. Insert fittings on beam assembly into tracks and move beam forward or aft to proper location where pins snap down into track.
C. Push right panel on outboard support arm and insert hanger pins into lower beam fittings. Ensure that all seal strip edges point forward.
CAUTION: DO NOT MOVE INBOARD END OF PANEL FORWARD OR AFT AFTER BEGINNING OF INSERTION ON OUTBOARD SUPPORT ARM TO PREVENT DAMAGE TO SOCKET.
D. Push left panel on outboard support arm and insert hanger pins into lower beam fittings. Ensure that all seal strip edges point forward.
CAUTION: DO NOT MOVE INBOARD END OF PANEL FORWARD OR AFT AFTER BEGINNING OF INSERTION ON OUTBOARD SUPPORT ARM TO PREVENT DAMAGE TO SOCKET.
E. Locate center panel in opening and insert three hanger pins.
F. Locate upper beam segments and insert all pins from bottom up.
CAUTION: ANY PINS INCORRECTLY INSERTED IN CENTER AREA WILL PREVENT DECOMPRESSION PANEL FROM FUNCTIONING.
G. Ensure that partition is vertical and tighten outboard support arm clamp on air conditioning extrusion. Tighten to 40 to 60 pound-inches.
H. Locate bottom of decompression panel on ball detents from forward side of partition and rotate top into place. Insert hanger pins.
506
Nov 01/75 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 25-24-152 Page 405
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737 AMM 飞机维护手册 EQUIPMENT/FURNISHINGS(88)
