H58929
517 Passenger Cabin Escape Straps
Oct 20/89 Figure 1 25-61-100
Page 1
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
ESCAPE ROPES/STRAPS (PASSENGER CABIN) - REMOVAL/INSTALLATION
1. Equipment and Materials
A. Tape - 0.25 inch aluminum tape, 3M 425 (Ref 20-30-51)
2. Remove Escape Strap Assembly (Fig. 401)
A. Remove emergency hatch (Ref Chapter 52, Emergency Exit Hatches).
B. Remove hook from retainer and withdraw strap from tube.
NOTE: Grasp center loop and pull all six lengths of strap from stowage tube.
C. Disconnect anchor, remove spacer and strap assembly.
3. Install Escape Strap Assembly (Fig. 401)
A. Locate spacer and bolt anchor in place.
B. On airplanes with anchor fitting on same side of escape hatch as hook retainer, fold strap into six lengths and wrap two to four times with aluminum tape in three places as shown in detail B, insert strap into tube.
C. Fasten hook in retainer.
D. Replace emergency exit hatch.
500
May 01/99 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 25-61-100 Page 401
H60726
Escape Strap Installation 517
25-61-100 Figure 401 May 01/99
Page 402
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
ESCAPE ROPES/STRAPS (PASSENGER CABIN) -INSPECTION/CHECK
1. Escape Strap Assembly Check
A. Check Escape Strap Assembly (Fig. 601).
(1)
Check strap for fraying, wear, moisture and mildew.
(2)
Check security of anchor fitting.
(3)
Check condition and security of hook.
(4)
Check strap is correct length.
500 Escape Strap Check
Jun 20/84 Figure 601 25-61-100
Page 601
B
O
E
I
NG P
R
OP
RI
E
T
A
R
Y
- Copyri
ght
. - Unpubl
i
s
hed W
o
rk
- S
ee t
i
t
l
e page f
o
r det
ai
l
s
.
ESCAPE ROPES/STRAPS (CONTROL CABIN ) - REMOVAL/INSTALLATION
1. General
A. An escape strap is attached above the captain's and the first officer's locations (Fig. 1). On some airplanes, escape straps are made from webbing assemblies impregnated with neoprene latex solution. On all other airplanes, escape straps (lanyards) of Kevlar fabric with handholds of Rohacell foam are installed.
B. The two escape straps are stowed in separate compartments above the captain's and first officer's seats. The fixed end of the strap is anchored to the overhead structure at these locations. Access to the escape strap is gained by unfastening the retainer which holds the strap in the compartment.
H58932
501 Escape Strap Installation
Jun 20/85 Figure 1 25-61-200
Page 1
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
ESCAPE ROPES/STRAPS (CONTROL CABIN ) - REMOVAL/INSTALLATION
1. Remove Escape Strap/Lanyard Assembly (Fig. 401)
A. Unlatch and open cover and remove escape strap.
B. Lift anchor fitting against spring, and disengage anchor stud from structure.
C. Remove escape strap assembly.
2. Install Escape Strap/Lanyard Assembly (Fig. 401)
A. Engage anchor stud in anchor fitting and check that it is secure.
B. Roll escape strap into a coil and place in its overhead position.
C. Place cover in position to cover and hold escape strap in place while securing cover.
501
Jun 20/85 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 25-61-200 Page 401
中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址:737 AMM 飞机维护手册 EQUIPMENT/FURNISHINGS(143)