ESCAPE SLIDE PACKAGE (DOOR-MOUNTED) - ADJUSTMENT/TEST
1. General
A. This procedure provides instructions for a system test of the door-mounted escape slide system at each entry or service door.
2. Equipment and Materials
A. Protective Pad - Ensolite - 1 inch x 48 inches - commercially available.
3. Test Door-Mounted Escape slide
A. Install a protective pad to the external airplane skin panel below the door. Tape the pad to airplane skin to prevent ingestion by the slide aspirator.
CAUTION: PLACE A PROTECTIVE PAD ON THE FUSELAGE SKIN. THE FUSELAGE SKIN COULD BE DAMAGED BY THE AIR CYLINDER IF THE SYSTEM IS TESTED WITHOUT THE PROTECTIVE PAD IN POSITION.
NOTE: We also recommend that you lay carpet on the surface where the slide will fall to protect the slide from abrasions.
B. Close and latch the entry or service door.
WARNING: CLEAR ALL PERSONNEL AND EQUIPMENT FROM THE PATH OF DEPLOYING SLIDE INSIDE AND OUTSIDE OF THE ENTRY/SERVICE DOOR. THE SLIDE INFLATES WITH A GREAT FORCE. SERIOUS INJURY TO PERSONNEL OR DAMAGE TO EQUIPMENT COULD OCCUR FROM CONTACT WITH THE SLIDE.
C. Make sure the needle on the pressure gage is within the green band.
D. Make sure the girt bar floor bracket fittings are clear of any obstructions.
E. Remove the girt bar from the retainer hooks on slide cover and install the girt bar into the floor bracket fittings.
F. Open the door in a normal manner. DO NOT HESITATE. Continue pushing the door to fully open.
G. Make sure the slide is opened and inflated to usable condition within 10 seconds after the compartment latch assembly is released.
H. Restore airplane to normal.
(1)
Do the escape slide/assembly restoration (Ref 25-61-311 MP [Restoration]).
(2)
Remove the protective pad from the airplane skin below door.
500
Jun 20/89 25-61-311
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Page 501
ESCAPE SLIDE BATTERY - INSPECTION/CHECK
EFFECTIVITY
Airplanes with Door-Mounted Escape Slide Integral Lighting System
1. Check Battery Voltage
A. Equipment and Materials
(1) Test Unit - TU-12 or TU-14, DME Corp., 111 SW 33rd Street, Ft Lauderdale, FL 33315
B. Test battery voltage of lighting system without unpacking slide as follows:
(1)
Remove slide package from door and open package without disconnecting latch cable (Ref R/I).
(2)
Open valise sufficiently to expose switch pin/lanyard and power unit test connector (Fig. 601).
(3)
Check power unit expiration date. Replace if expiration date is sooner than next scheduled maintenance date.
(4)
Check that all electrical connections between lamp harness, power unit, test set, and test adapter are positioned and that switch pin/lanyard is installed in power unit.
(5)
Set load selector knob to B.
(6)
Install four pin test connector from the power unit in test receptacle.
(7)
Move test unit arm switch to ARM position.
(8)
Depress test unit activate switch to activate test unit.
(9)
Depress the Lamp-Test-Button until the ampere reading on ammeter is stabilized. Release the Test Button; the ampere reading must be greater than 0.730 with the TU-12 test unit or greater than 0.770 with the TU-14 test unit.
CAUTION: CHECK THAT THE SWITCH PIN/LANYARD IS INSTALLED IN POWER UNIT. NOT INSTALLING SWITCH PIN/LANYARD WILL DISCHARGE POWER UNIT.
May 01/98 25-61-312 Page 601
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
Escape Slide Installation 500
25-61-312 Figure 601 Jun 20/92
Page 602
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
ESCAPE SLIDE FLOOR BRACKETS - MAINTENANCE PRACTICES
1. Equipment and Materials
A. Solvent - BMS 3-2 (Ref 20-30-31)
B. Sealant - BMS 5-18, Type II; BMS 5-19, Class B; or BMS 5-22 (Ref 20-30-11)
C. Gauze cleaning cloth
D. Shim - Mylar sheet (type A per MIL-T-23142) 0.01 thick, 3.50 x 2.50 inches
2. Escape Slide Floor Bracket - Removal/Installation (See figure 201.)
A. Remove bracket.
(1)
Remove two pan head bolts and lock washers.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737 AMM 飞机维护手册 EQUIPMENT/FURNISHINGS(147)
