(a) Remove the two hinge pins from the mobile workstand.
(b) Move the half door to the 45 degrees position with the handling sling.
(c) Put the half door in a position to align the hinges with the hinges of the mobile workstand.
(d) Install the hinge pins through the hinges of the half door and the mobile workstand and install the cotter pins.
(20) Remove the handling sling from the half door (Ref. Fig. 404/TASK 78-32-11-991-305, 405/TASK 78-32-11-991-306)
(21) Install the attachment strap on the lower hoist point of the half door.
F 『 EEFF : ALL E Page 41478-32-11
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 78-32-11-400-002
Installation of the Left or Right Half Door of Thrust Reverser
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
No specific access platform 1 m (3 ft. 3 in.)
No specific Torque Wrench : range 35 to 45 lbf.in
(0.39 to 0.50 m.daN)
No specific Torque Wrench : range 36.00 to 220.00 lbf.in
(0.40 to 2.60 m.daN)
No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00 to 10.00 m.daN)
HIX1001 1 HANDLING SLING
HIX3001 1 WORKSTAND MOBILE
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. CP2104 *
molykote G rapid (Ref. 70-30-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
R 10 cotter pin 78-32-11 01A-050
F 『 EEFF : ALL E Page 41578-32-11
E E Aug 01/03 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
71-13-00-410-040 Closing of the Fan Cowl Doors
71-13-00-800-041 Adjustment of the Fan Cowl Doors
71-13-11-400-041 Installation of the Fan Cowl Doors
78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance 78-30-00-710-040 Thrust Reverser Hydraulic System Bleed Procedure 78-31-00-710-042 Operational Test of the Thrust Reverser System 78-31-00-710-043 Operational Test of the Thrust Reverser without CFDS
- Engine Not Running 78-31-00-710-043 Operational Test of the Thrust Reverser without CFDS
- Engine Running 78-36-00-410-040 Closing of the Thrust Reverser Doors 78-36-41-820-042 Adjustment of the Thrust Reverser Half Door Latches
R 78-36-42-820-002 Adjustment of the LH or R/H Thrust Reverser "J" Ring R on Wing 78-36-51-400-041 Installation of the Thrust Reverser Half Door Opening
Actuator
78-32-11-991-302 Fig. 401
78-32-11-991-303 Fig. 402
78-32-11-991-304 Fig. 403
78-32-11-991-305 Fig. 404
78-32-11-991-306 Fig. 405
78-32-11-991-307 Fig. 406
78-32-11-991-308 Fig. 407
3. Job Set-up
__________
Subtask 78-32-11-860-051
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
F 『 EEFF : ALL E Page 41678-32-11
E E Aug 01/05 E E ECES E E 56-5B E
F 『
E C F M E
E E
E E
(3) Make sure that the access platform is in position. 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM EXHAUST 2(52)
